Search Results for bump pitch

This article discusses the types and operations of the most common machines used for die threading. The construction, types, and comparison of solid and self-opening dies are discussed. The article explains the modification of chasers for threading Monel shaft. The principal factors that influence thread quality, production rate, and cost in die threading are composition and hardness of work metal; accuracy and finish; thread size; obstacles, such as shoulders or steps; speed; lead control; and cutting fluid. The article examines these factors and describes the tools and cutting fluids used for pipe threading along with the severity of stop lines.

This article describes the characteristics of three types of gas bearings, such as aerostatic bearing, precision aerodynamic bearing (PAB), and compliant aerodynamic bearing (CAB). It discusses the applications for aerostatic bearings and advantages in lubricating a bearing with a compressible gas. The article also describes the different types of aerostatic bearings, such as annular thrust bearings and orifice-compensated journal bearings. It presents a discussion on load capacity and stiffness, friction and power loss, and stability and damping of the aerostatic bearings. The article provides a discussion on the types of PAB and CAB. The types include spiral groove annular thrust bearings, cylindrical journal bearings, three-sector journal bearings, tilting-pad journal bearings, and helical-grooved journal bearings. The types of CAB include foil bearings and pressurized-membrane bearings. The article concludes with a description of factors that influence materials selection for gas-lubricated bearings.

The role of a mixer/agitator in quenching applications is to control the mixing environment in order to meet the process criteria. This article provides the basic fundamentals of the sizing of agitators, tank geometry importance, and other considerations for the application of agitators in quench tanks. It also discusses the differing methods for the sizing and selection of agitators for quench tank applications.

Soldering represents the primary method of attaching electronic components, such as resistors, capacitors, or packaged integrated circuits, to either printed wiring board whose defects is minimized by consideration of proper PWB design, device packages, and board assembly. This article discusses the categories that are most important to successful electronic soldering, namely, solders and fluxes selection, nature of base materials and finishes, solder joint design, and solderability testing.

This article provides information on various forms of corrosion that occur in electronic packaging. Portable consumer electronic hardware which is subjected to humidity exposures is prone to condensed moisture and liquid damage. The article discusses two other corrosion-related phenomena that are found only in electronics, namely, electrochemical migration (ECM) and conductive anodic filament formation (CAF). It describes the corrosion that takes place in metals such as copper, tin, and tin-lead alloys, which are commonly used in electronic packaging. The article also discusses the corrosion of the components used in electronic assemblies.

This article introduces the principal methodologies and some technologies that are being applied for nondestructive evaluation of composite materials. These include ultrasonic testing (UT), air-coupled UT, laser UT, ultrasonic spectroscopy, leaky lamb wave method, acousto-ultrasonics, radiography, X-ray computed tomography, thermography, low-frequency vibration methods, acoustic emission, eddy current testing, optical holography, and shearography. The article presents some examples are for fiber-reinforced polymer-matrix composites. Many of the techniques have general applicability to other types of composites such as metal-matrix composites and ceramic-matrix composites.

This article presents a comprehensive collection of the definition of terms related to metallurgy.

This article emphasizes the traits that are common to high-velocity forming operations. It describes general principles on how metal forming is accomplished and analyzed when inertial forces are large. The article discusses the principal methods of high-velocity forming, such as explosive forming, electrohydraulic forming, and electromagnetic forming. It provides examples that illustrate how these methods can be practically applied. The article concludes with information on the status and development potential for the technology.

Flame hardening is a heat treating process in which a thin surface shell of a steel part is heated rapidly to a temperature above the critical temperatures of the steel. The versatility of flame-hardening equipment and the wide range of heating conditions obtainable with gas burners, often permit flame hardening to be done by a variety of methods. These include the spot or stationary method, progressive method, spinning method, and the combination progressive-spinning method. This article provides information on fuel gases used in flame hardening and their selection criteria for specific applications. It also discusses operating procedures and control requirements for flame hardening of steel.

Tribology is the science and technology of interacting surfaces in relative motion. This article describes in detail the basic structural, operational, and interaction parameters of a tribosystem. The interaction parameters, which characterize the action of the operational parameters on the structural components in the system, consist of three important aspects: contact parameters, friction parameters, and wear parameters. These three aspects embody the complex mechanisms and relationships between the constituents of a tribosystem. The article concludes with information on the selection criteria of a material for wear applications.

Adhesive-bonded joints are extensively used in aircraft components and assemblies where structural integrity is critical. This article addresses the problem of how to inspect bonded assemblies so that all discrepancies are identified. It describes several inspection techniques and presents drawbacks and limitations of these techniques. Generic flaw types and flaw-producing mechanisms are listed in a table. The article discusses metal-to-metal defects, adherend defects, honeycomb sandwich defects, repair defects, and in-service defects. It reviews the methods applicable to the inspection of bonded structures, including visual inspection, ultrasonic inspection, X-ray radiography, and neutron radiography. The evaluation and correlation of inspection results are also discussed. The article concludes with information on the effects of ultrasonic wave interference in the ultrasonic inspection of adhesive-bonded joints.

Impact tests are used to study dynamic deformation and failure modes of materials. This article discusses low-velocity impact experiments in single-stage gas guns. It describes surface velocity measurements with laser interferometric techniques. The article details plate impact soft-recovery experiments, pressure-shear friction experiments, and low-velocity penetration experiments. It reviews two types of plate impact soft-recovery experiments: normal plate impact and pressure-shear plate impact experiments. The article provides information on low-velocity penetration experiments, which include the setup for direct penetration experiment (rod-on-plate) and the reverse penetration experiment (plate-on-rod). It also considers high-temperature plate impact testing and impact techniques with in-material stress and velocity measurements.

This article is a compilation of definitions for terms related to engineering materials, including plastics, elastomers, polymer-matrix composites, adhesives and sealants, ceramics, ceramic-matrix composites, glasses, and carbon-carbon composites.

Painting is a generic term for the application of a thin organic coating to the surface of a material for decorative, protective, or functional purposes. This article provides a detailed account of the types and selection factors of paints and the various application methods, including conventional air atomized, airless, and electrostatic spray; roller coating; dip coating; flow coating; curtain coating; tumble coating; electrocoating; and powder coating. Surface preparation methods and prepaint treatments for coating systems are also discussed. The article includes information on quality control procedures, causes of paint film defects, cost calculation, and safety and environmental precautions. The composition and characteristics of organic coatings, coating system selection factors, the types of paints for structural steel, and the applications of paint on structural steel are also reviewed.