1-13 of 13 Search Results for

automotive sheet alloy 6022

Sort by
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006712
EISBN: 978-1-62708-210-5
... Abstract The automotive sheet alloy 6022 provides improved corrosion resistance, higher formability, and greater strength for dent resistance after thermal exposure compared with other automotive sheet alloys. This datasheet provides information on key alloy metallurgy, processing effects...
Book Chapter

By Jian Cao
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005166
EISBN: 978-1-62708-186-3
... – 17 10.1016/0924-0136(96)02281-9 2. Friedman P.A. and Luckey S.G. , Bendability of Al-Mg-Si Sheet Alloys for Automotive Closure Applications , TMS Annual Meeting , 2001 , p 3 – 15 3. Dao M. and Li M. , A Micromechanics Study on Strain-Localization-Induced...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005168
EISBN: 978-1-62708-186-3
... Abstract This article discusses the numerical simulation of the forming of aluminum alloy sheet metals. The macroscopic and microscopic aspects of the plastic behavior of aluminum alloys are reviewed. The article presents constitutive equations suitable for the description of aluminum alloy...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003223
EISBN: 978-1-62708-199-3
... of extrusion alloys is the most critical; they cannot be made using very much scrap. Many sheet grades can tolerate a high percentage of scrap, but certain grades (many automotive) must be excluded from the charge. Alloys for die and gravity casting, on the other hand, can tolerate widely mixed aluminum scrap...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006516
EISBN: 978-1-62708-210-5
... … 0.006 0.002 0.005 0.005 … Source: Ref 3 These alloys are used in the O temper in many different sheet and foil applications that require good formability and corrosion resistance but limited strength requirements. Flexible tubes (made from sheet), duct sheet, automotive heat shields...
Series: ASM Handbook
Volume: 22B
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.hb.v22b.a0005528
EISBN: 978-1-62708-197-9
... are provided. Experimental Studies for Material and Process Characterization This section discusses results of some experiment studies with two aluminum alloys, 6022-T4 and 5182-H19, that were conducted at Alcoa Technical Center using a double-action laboratory die. The aluminum sheet was clamped...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005131
EISBN: 978-1-62708-186-3
... by springback can be very significant even though the elastic strains driving the springback can be tiny. Fig. 1 Typical automotive sheet-formed part, the S-rail. (a) Formed part. (b) Finite element representation, as formed. (c) Cross-sectional schematics at three forming stages. Source: Ref 1...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006518
EISBN: 978-1-62708-207-5
... in various literature and specifications as T736-type tempers. Source: Ref 1 Wrought aluminum product specifications Table 2 Wrought aluminum product specifications Alloy Product Specifications ASTM Military Federal AMS ASME AWS 1060 Sheet and plate B 209 … … … SB209...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003125
EISBN: 978-1-62708-199-3
... in the 1 xxx , 2 xxx , 3 xxx , 5 xxx , and 7 xxx series are available in sheet form (see Table 1 ). Along with alloy 6061, they cover a wide range of applications from builders' hardware to transportation equipment and from appliances to aircraft structures. Alloys 6009, 6111, and 6022 are widely used...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006543
EISBN: 978-1-62708-210-5
... treatment, and precipitation aging. Wrought products then include rolled sheet and plate, rolled and drawn shapes, forgings, extrusions, and a few other specialty products. The use of aluminum alloy wrought products, especially sheet, plate, forgings, and extrusions, has continued to increase over the years...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006546
EISBN: 978-1-62708-210-5
... of copper. Alloys of this type were the first heat treatable high-strength aluminum-base materials, and they have been used for more than 75 years in structural applications, particularly in aircraft and aerospace applications ( Ref 15 ). Much of the thin sheet made of these alloys is produced as an alclad...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003815
EISBN: 978-1-62708-183-2
... of other series, which contain much lower amounts of copper. Alloys of this type were the first heat treatable high-strength aluminum-base materials and have been used for more than 75 years in structural applications, particularly in aircraft and aerospace applications ( Ref 16 ). Much of the thin sheet...
Series: ASM Handbook
Volume: 4E
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.hb.v04e.a0006268
EISBN: 978-1-62708-169-6
... phases in Al-Mg-Si-Cu engineering alloys Field Phase Alloys I α, θ, β, Q High-magnesium:silicon alloys, e.g., 6061 and 2017 II α, θ, (silicon), Q Low-magnesium: silicon alloys, e.g., 6111 and 2014 III α, β, (silicon), Q Low-copper alloys, e.g., 6022 IV α, θ, S (or T), and β...