1-20 of 1160

Search Results for aluminum-magnesium alloys

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 4C
Publisher: ASM International
Published: 09 June 2014
DOI: 10.31399/asm.hb.v04c.a0005887
EISBN: 978-1-62708-167-2
... Abstract This article focuses on the temperature requirements of typical nonferrous metals and their alloys of commercial importance. These include aluminum, copper, magnesium, and titanium. The article describes the thermoelectricity, photoelectricity, and capacity of aluminum alloys...
Image
Published: 15 June 2019
Fig. 25 Fatigue strength comparison for aluminum alloys, magnesium alloys, and steels. Source: Ref 29 More
Book Chapter

Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006694
EISBN: 978-1-62708-210-5
... Abstract The general-purpose alloy 5050 is a binary aluminum-magnesium alloy with more magnesium content than 5005. This datasheet provides information on key alloy metallurgy, processing effects on physical and mechanical properties, and fabrication characteristics of this 5xxx series alloy...
Image
Published: 01 January 1996
Fig. 10 Stress vs. time-to-failure (t f ) for magnesium-aluminum alloys in aqueous 40 g/L NaCl + 40 g/L Na 2 CrO 4 . Source: Ref 28 More
Image
Published: 01 December 2004
Fig. 5 Typical examples of aluminum-magnesium commercial alloys. (a) Microstructure showing Al 3 Fe (gray) and Mg 2 Si (black) in α-aluminum solid-solution matrix (alloy type A518 with 7.6% Mg). Etchant: 0.5% HF. Original magnification 560×. (b) Microstructure showing ternary eutectic and α More
Image
Published: 30 November 2018
Fig. 17 Effect of magnesium on aging response of aluminum-copper alloys. Source: Ref 21 More
Image
Published: 30 November 2018
Fig. 29 Effect of magnesium and manganese on the formability of aluminum alloys in the annealed and H34 tempers; 1.6 mm (0.064 in.) thick sheet More
Image
Published: 01 January 2005
Fig. 12 Stress versus time to failure ( t f ) for magnesium-aluminum alloys in aqueous 40 g/L NaCl+40 g/L Na 2 CrO 4 . Source: Ref 23 More
Image
Published: 01 January 1990
Fig. 14 Effect of magnesium and manganese on the formability of aluminum alloys in the annealed and H34 tempers; 1.6 mm (0.064 in.) thick sheet More
Image
Published: 01 June 2016
Fig. 9 Effect of magnesium in solution on the tensile properties of annealed aluminum-magnesium alloys. Source: Ref 35 More
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006581
EISBN: 978-1-62708-210-5
... characteristics, processing effects on physical and mechanical properties, and applications of these alloys. aluminum alloy 511.0 aluminum alloy 512.0 aluminum alloy 513.0 aluminum-magnesium alloys fabrication characteristics mechanical properties moderate-strength casting alloys physical properties...
Image
Published: 01 January 2005
Fig. 35 Alligatoring in a rolled slab. This defect is thought to be caused by nonhomogeneous deformation and nonuniform recrystallization during primary rolling of such metals as zinc alloys, aluminum-magnesium alloys, and copper-base alloys. Courtesy of J. Schey, University of Waterloo More
Image
Published: 30 November 2018
Fig. 15 Relationship between room-temperature hardness and subgrain size for aluminum and aluminum-magnesium alloys. Source: Ref 13 More
Image
Published: 01 January 2005
Fig. 5 Strain to failure as a function of deformation temperature for an aluminum-magnesium alloy homogenized by different schedules More
Image
Published: 01 January 2005
Fig. 4 Flow stress as a function of deformation temperature for an aluminum-magnesium alloy homogenized by different schedules (#1, #2, #3, #4) More
Image
Published: 31 October 2011
Fig. 9 Macrostructure samples from joints after laser roll welding of low-carbon steel sheet (JIS-SPCC) with (a) A1050 aluminum and (b) aluminum-magnesium alloy A5052. Laser power, welding speed, and roll pressure were: (a) 1.5 kW, 1.5 m/min (4.9 ft/min), and 150 MPa (22 ksi) for A1050, and (b More
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0009012
EISBN: 978-1-62708-185-6
... Example 1: Extrusion of Al-Mg Alloy An extrusion fabricator considered extruding a proprietary aluminum-magnesium (5 xxx ) alloy that is very similar in composition to an alloy that is usually hot rolled. From rolling practice, it is known that this alloy is sensitive to homogenization schedule...
Book Chapter

Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006706
EISBN: 978-1-62708-210-5
... Abstract This datasheet provides information on key alloy metallurgy and processing effects on physical and mechanical properties of Al-3.1Mg alloy 5754. aluminum-magnesium alloy 5754 mechanical properties physical properties Alloy 5754 ( Table 1 ) is closely related to the alloys...
Book Chapter

By Ralph Dorward
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006487
EISBN: 978-1-62708-207-5
...-worked materials with strengths initially greater than desired H3 Strain hardened and stabilized H32, H34, H36, H38: Tempers for age softening aluminum-magnesium alloys that are strain hardened and then heated at a low temperature to increase ductility and stabilize mechanical properties H112...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005302
EISBN: 978-1-62708-187-0
... alloys, aluminum-silicon-copper casting alloys, aluminum-zinc-magnesium casting alloys, and aluminum-magnesium casting alloys. The article also examines the benefits of grain refinement in aluminum casting alloys. boron fatigue strength grain refinement grain size mechanical properties...