1-20 of 41 Search Results for

aluminum alloy 514.0

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006582
EISBN: 978-1-62708-210-5
... for aluminum alloy 514.0-F, permanent mold. Specimen: 28.575 diam × 305 mm (1.125 diam × 12 in.) rod. Source: Ref 1 Abstract Abstract This datasheet provides information on key alloy metallurgy, foundry characteristics, processing effects on physical and mechanical properties, and applications...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006581
EISBN: 978-1-62708-210-5
... a modification of 514.0, used in ornamental hardware and architectural castings with improved foundry characteristics ( Ref 1 ). The silicon content of 511.0 is about one-third that of Alloy 512.0 and gives a more uniform appearance. Magnesium in aluminum alloys increases oxidation rates. In the molten state...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006585
EISBN: 978-1-62708-210-5
... 2 230 450 169 24.5 2 260 500 190 27.5 5 315 600 260 38 15 370 700 275 40 16 425 800 275 40 16 480 900 275 40 16 General fabrication characteristics of alloys 514.0, 520.0 and 535.0 Table 6 General fabrication characteristics of alloys 514.0, 520.0...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006623
EISBN: 978-1-62708-210-5
...Relative rating of selected aluminum filler alloys used to fillet weld or butt weld two-component base alloys Table 1 Relative rating of selected aluminum filler alloys used to fillet weld or butt weld two-component base alloys Data are for welded assemblies not heat treated after welding...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001436
EISBN: 978-1-62708-173-3
... with aluminum alloys Table 13 Recommended filler alloys used to obtain best color match with aluminum alloys Aluminum alloy Filler alloy 1100, 3003, 5005, 5050 1188 5052, 5154 5654 6061, 6063, 511.0, 514.0, 535.0 5356 5083, 5086, 5454, 5456 5183 or 5556 356.0, A356.0, A357.0...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002184
EISBN: 978-1-62708-188-7
...Abstract Abstract This article begins with a discussion on the classification of aluminum alloys and the selection of alloy and temper based on machinability. It provides an overview of cutting force and power, tool design and material, and general machining conditions. In addition, the article...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006691
EISBN: 978-1-62708-210-5
... potential of aluminum alloys in NaCl-H 2 O 2 solution Aluminum alloy (a) Potential volts 0.1 N calomel scale (b) Filler alloy A712.0 −0.99 … Alclad 3003, alclad 6061, 7072 −0.96 … 7005-T6, 7039-T6 −0.93 to −0.96 … 5083, 5456, 514.0 −0.87 5183, 5356, 5556 5154, 5254, 5454...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003128
EISBN: 978-1-62708-199-3
...Typical physical properties of aluminum casting alloys Table 1 Typical physical properties of aluminum casting alloys Aluminum Association No. Temper (a) Specific gravity (b) Density (b) Approximate melting range Electrical conductivity, %IACS Thermal conductivity at 25 °C...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006510
EISBN: 978-1-62708-207-5
... Filler alloys suggested for welding select aluminum-base alloys to minimize sensitivity to weld cracking Base metal 319.0, 333.0, 354.0, 355.0, C355.0, 380.0 356.0, A356.0, A357.0, 359.0, 413.0, A444.0, 443.0 511.0, 512.0, 513.0, 514.0 7005 (a) , 7039, 710.0, 711.0, 712.0 6070 6061, 6463, 6101...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003127
EISBN: 978-1-62708-199-3
... requiring strength without heat treatment or involving brazing Other aluminum alloys commonly used for sand castings include 319.0, 355.0, 356.0, 514.0, and 535.0. Specifications for sand-cast aluminum alloys are cross referenced in Table 1 . In this process the mold cavity is formed by a shell...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006625
EISBN: 978-1-62708-210-5
...) Ingot; 1.5 min Fe/Si ratio. (f) Also contains 0.40–1.0% Ag (0.7% nominal). (g) Also contains 0.20–0.30% Sb (0.25% nominal), 0.20–0.30% Co (0.25% nominal), and 0.10–0.30% Zr. Ti + Zr contents = 0.50% max. (h) Alloy has been designated “Inactive” by The Aluminum Association but still occurs...
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001061
EISBN: 978-1-62708-162-7
...Factors affecting selection of casting process for aluminum alloys Table 7 Factors affecting selection of casting process for aluminum alloys Factor Casting process Sand casting Permanent mold casting Die casting Cost of equipment Lowest cost if only a few items required Less...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0006543
EISBN: 978-1-62708-183-2
..., and lead, and their alloys. aluminum copper corrosion rate density iron lead magnesium stainless steels DENSITY allows for conversion of uniform corrosion rates from units of weight (or mass) loss per unit area per time, to thickness per unit time. These density values are for room...
Series: ASM Handbook
Volume: 4E
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.hb.v04e.a0006251
EISBN: 978-1-62708-169-6
...Typical mechanical properties (in customary units) of wrought aluminum alloys in various temper conditions Table 4 Typical mechanical properties (in customary units) of wrought aluminum alloys in various temper conditions Alloy and temper (a) Tension Hardness, Brinell No., 500 kg load...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006482
EISBN: 978-1-62708-207-5
...Abstract Abstract Commercial aluminum alloys are classified based on how they are made and what they contain. This article describes the ANSI H35.1 designation system, which is widely used to classify wrought and cast aluminum alloys. The ANSI standard uses a four-digit numbering system...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001417
EISBN: 978-1-62708-173-3
...Alloy designations of wrought aluminum alloys Table 1 Alloy designations of wrought aluminum alloys Alloy system Aluminum series Work-hardenable alloys Pure Al 1 xxx Al-Mn 3 xxx AI-Si 4 xxx Al-Mg 5 xxx Al-Fe 8 xxx Al-Fe-Ni 8 xxx Precipitation...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006553
EISBN: 978-1-62708-210-5
...Abstract Abstract This article summarizes some general alloy groupings by application or major characteristics. The groupings include cast rotor, general-purpose, elevated-temperature, wear-resistant, moderate-strength, high-strength, and high-integrity die casting alloys and cast aluminum...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006568
EISBN: 978-1-62708-210-5
... type test Tensile properties of representative squeeze-cast aluminum alloy castings Table 4 Tensile properties of representative squeeze-cast aluminum alloy castings Alloy Temper Casting process Tensile strength Yield strength, 0.2 % offset Elongation in 50 mm (2 in.) or 4D...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003082
EISBN: 978-1-62708-199-3
...Abstract Abstract This article contains tables that present engineering data for the following metals and their alloys: aluminum, copper, iron, lead, magnesium, nickel, tin, titanium, zinc, precious metals, permanent magnet materials, pure metals, rare earth metals, and actinide metals. Data...
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001062
EISBN: 978-1-62708-162-7
...Abstract Abstract This article is a compilation of property data for standard grades of cast aluminum alloys. Data are provided for mechanical, thermal, and electrical properties. The listing for each alloy includes commercial names, chemical compositions, applications, relevant specifications...