1-20 of 366 Search Results for

adhesive bond specimen

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003365
EISBN: 978-1-62708-195-5
... and resin disks, adhesive film, adhesive bond specimens, and films. References References 1. Harris F.W. , Hsu S.L.C. , and Tso C.C. , Synthesis and Characterization of Polyimides Based on 2,2′ Bis (Trifluoromethyl)-4,4′-Diaminobiphenyl , Polym. Prepr ., Vol 31 ( No. 5 ), 1990...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001468
EISBN: 978-1-62708-173-3
... adhesively bonded joint design. A fastener load-distribution curve is shown in Fig. 13 . The test specimen was designed for a zero margin at 150% of design limit load (DLL); failure occurred at 173% DLL. The specimen failed as predicted at the end fastener hole (fastener No. 1) in the high bypass strain...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003324
EISBN: 978-1-62708-176-4
... of engineering design data : To predict the load-carrying capability of a given bonded joint The geometry of the test specimen selected is very important even for quality control tests. In fact, an adhesive that exhibits “high strength” in a tensile test may have poor peel strength and vice versa. In fact...
Series: ASM Handbook
Volume: 17
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.hb.v17.a0006457
EISBN: 978-1-62708-190-0
... flatwise tension specimens are fabricated and tested to determine if the process meets specification requirements before the bonding cycle starts. Considerable effort at Fokker in the Netherlands led to the important discovery that the ideal oxide configuration for adhesion on aluminum alloys can...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003444
EISBN: 978-1-62708-195-5
.... 3 Static and fatigue ply drop-off test specimen. (1) Bond fiberglass-epoxy tabs with epoxy film adhesive. (2) Specimen thickness shall not vary more than ±0.13 mm (0.005 in.). (3) Specimen longitudinal edges shall be parallel to 0.13 mm (0.005 in.). (4) Top end and bottom end surfaces shall...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006530
EISBN: 978-1-62708-207-5
...Abstract Abstract Adhesive bonding is a proven technology in the manufacture of automotive assemblies, helping carmakers achieve weight reduction goals without compromising body stiffness, crash performance, and noise-vibration-handling characteristics. This article discusses the advantages...
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.a0005730
EISBN: 978-1-62708-171-9
...-chromium-aluminum coating used to study the tensile adhesion test as listed in Table 1 Fig. 4 Standard V-block set at an incline for gravity bonding of tensile specimens Fig. 25 Schematic of the block-on-ring apparatus Fig. 24 Schematic of the pin-on-disk apparatus...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003467
EISBN: 978-1-62708-195-5
.... The blade failure consisted of a complete separation of the outer carbon/epoxy sleeve from the internal Kevlar/epoxy paddle, as well as complete transverse failure of the paddle and the sleeve ( Fig. 1 ). The outer sleeve and the paddle are manufactured separately and then adhesively bonded together during...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006375
EISBN: 978-1-62708-192-4
... and by a factor of 13 with an aluminum-sapphire couple. Thus, contamination is an important factor in determining such solid surface properties as adhesion in vacuum environments. Contaminant layers can greatly reduce adhesion. Adhesion, a manifestation of atomic bond strength over an appreciable area, has...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003043
EISBN: 978-1-62708-200-6
... recording is generated during the test to assist in the determination of joint yield load (yield is defined as the load at which the specimen would have taken a permanent deformation at 4% of nominal fastener diameter, following removal of load). The main advantage of PCM welding over adhesive bonding...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003046
EISBN: 978-1-62708-200-6
...-Epoxy Patch Repairs Thermoplastics have been shown to be tougher and more damage resistant than thermosets, but have not been fully specified for repair applications in terms of adhesive bonding and reprocessing parameters. Economic tradeoffs will come into play with the use of thermoplastics...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001348
EISBN: 978-1-62708-173-3
... adhesion adhesion energy bonding grain boundary energy interfacial characterization interfacial energy mechanical properties metal adhesion metal-to-ceramic adhesion solid-state welding strength Abstract Abstract This article reviews quantifying adhesion, bonding...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003452
EISBN: 978-1-62708-195-5
...Abstract Abstract Composite bonded repair technology is based on the use of advanced composite repairs or reinforcements that are adhesively bonded to a damaged structure. This article discusses the key steps that are normally encountered in the design, certification, and application...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003489
EISBN: 978-1-62708-195-5
... H/G H/G H/Mod H/P … … Acrylics … … … L/P H/E M/G L/P … … Fig. 3 Load paths to avoid in adhesive use Fig. 1 Typical secondary adhesively bonded joint configurations. (a) Single lap joint. (b) Tapered single lap joint. (c) Single strap joint. (d) Double lap joint...
Series: ASM Handbook
Volume: 9
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.hb.v09.a0009076
EISBN: 978-1-62708-177-1
... and polished substrate. The selected resin must be low viscosity (that is, less than 300 cP mixed viscosity) to provide a very thin bondline. The lack of a homogeneous adhesive bond between the sample and the glass slide will decrease the quality of the thin section. Trapped air and/or contaminants can cause...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.9781627081955
EISBN: 978-1-62708-195-5
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003044
EISBN: 978-1-62708-200-6
... is similar to that used for metal: 0.2% strain, and the calculation is the same. Tensile testing of polymeric-matrix composites is based on ASTM D 3039. This method utilizes a straight-sided, constant-cross-section specimen with adhesively bonded end tabs for load introduction. For 0° unidirectional...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.9781627082006
EISBN: 978-1-62708-200-6
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003374
EISBN: 978-1-62708-195-5
.... , Nakajima A. , Ikada Y. and Suzuki T. , Adhesion and Bonding in Composites , Marcel Dekker, Inc. , New York , 1990 2. Drzal L.T. , Advances in Polymer Science II , Vol 75 Dusek K. , Ed., Springer-Verlag , 1985 3. Bascom W.D. and Drzal L.T...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003037
EISBN: 978-1-62708-200-6
... Sandwich Panel Testing Sandwich Concept Material Selection Considerations Adhesive Bonding Design Guidelines Honeycomb Properties Trimming Forming Splicing Machining A typical sandwich consists of two thin, high-strength facings bonded to a thick, lightweight core. Each...