1-20 of 106 Search Results for

abrasive-jet

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001232
EISBN: 978-1-62708-170-2
... discussion on abrasive jet machining and ultrasonic machining. It concludes with a discussion on the four categories of factors that affect the abrasive finishing or machining: machine tool, work material, wheel selection, and operational. abrasive belt grinding abrasive belt polishing abrasive...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003194
EISBN: 978-1-62708-199-3
... machining, electrical discharge machining, chemical machining, abrasive jet machining, laser beam machining, electron beam machining, ultrasonic impact grinding, hydrodynamic machining, thermochemical machining, abrasive flow machining, and electrical discharge wire cutting. abrasive jet machining...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003042
EISBN: 978-1-62708-200-6
... applications of water-jet cutting and abrasive water-jet cutting. aramid composites conventional machining techniques cutting systems drilling graphite composites laser cutting polymer-matrix composites water-jet cutting COMPOSITES, though superior to conventional materials in many physical...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001228
EISBN: 978-1-62708-170-2
... ventilation ducts. Check entire machine for possible wear holes through which abrasive might escape. Check rubber flaps at opening of machine for wear and escaping abrasives. Automatic air blast machines: daily Check all nozzles and air jets for wear and proper flow. Check media and air...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003186
EISBN: 978-1-62708-199-3
... conventional or abrasive processes and are generally used when the part geometry or material does not permit the use of any other operation. Table 1 Material removal categories of nontraditional machining processes Mechanical Abrasive jet machining (AJM) Abrasive flow machining (AFM...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003055
EISBN: 978-1-62708-200-6
... of the pad follows the contour of the workpiece and, in addition, tends to round off (wash off) the edges. In abrasive waterjet cutting, high-velocity water, rather than gas, is used to entrain and accelerate abrasive particles. Unlike gas jets, waterjets can be confined to a small diameter without...
Book

Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.9781627081887
EISBN: 978-1-62708-188-7
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006024
EISBN: 978-1-62708-172-6
... range from simple solvent cleaning to hand and power tool cleaning, dry and wet abrasive blast cleaning, chemical stripping, waterjetting, and nontraditional methods such as sponge jetting and cryogenic blast cleaning using dry ice pellets. Each of the traditional methods is briefly summarized...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006789
EISBN: 978-1-62708-295-2
... Abrasive wear by hard particles Fracture/deformation produced by hard, sharp particles or protuberances Solid-particle erosion Fracture/deformation from particle indents Cavitation erosion Fracture produced by impinging liquid jets Slurry erosion Fracture (from hard substances) conjoint with...
Book Chapter

By Peter J. Blau
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003242
EISBN: 978-1-62708-199-3
... Slurry Abrasivity (Miller Number) and Slurry Abrasion Resistance Response of Materials (SAR Number) Mass loss Erosive wear, solid particles G 76 Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets Mass loss Fretting wear D 4170 Test Method for Fretting Wear...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006061
EISBN: 978-1-62708-172-6
..., power tool cleaning, abrasive blast cleaning, water jetting, or any combination of these. Contract specifications often only reference specification requirements contained in other publications. In the United States, the Society for Protective Coatings (SSPC) or the National Association of Corrosion...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001298
EISBN: 978-1-62708-170-2
...-gage rosette (5.13 mm, or 0.202 in., strain-gage mean diameter) was attached to the coated specimen. A 2.44 mm (0.096 in.) diameter hole was cut in the WC-Co coating by abrasive-jet drilling using 27 μm (1080 μin.) alumina particles. Drilling proceeded in four approximately equal depth increments, up...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001238
EISBN: 978-1-62708-170-2
... in high levels of hydrogen in ground steel samples ( Ref 54 ). Other examples include a sanding technique that influences the wettability and shear strength of wood ( Ref 55 ) and abrasive jet machining finishing techniques that are used where there is risk of explosion. In many manufacturing...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006016
EISBN: 978-1-62708-172-6
... power tool cleaning, water jetting, and wet abrasive blast cleaning can be used to aid in the evaluation of surface cleanliness. These are described later in the article. In the event of a dispute, it is the written standards and not the visual guides that are the governing document. Examination is...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006794
EISBN: 978-1-62708-295-2
..., slurry-jet erosion, and cavitation-corrosion tests ( Fig. 4 ), which simulate different corrosive wear conditions. Figure 4(a) schematically illustrates a pin-on-disc tester in accordance with ASTM G 99 ( Ref 27 ) for evaluating abrasion or sliding wear, which can be conducted in a corrosive solution...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001230
EISBN: 978-1-62708-170-2
... finished bearings or a transmission, respectively. Computer parts such as microchips or magnetic heads may be ground, lapped, or polished before they are sent to assembly operations. Jet engine blades may have coolant holes drilled using electrical discharge machining or laser machining prior to their use...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006062
EISBN: 978-1-62708-172-6
... method is well suited for aluminum substrates; airlines use it for coating the exterior of planes. It is generally too costly and not aggressive enough for use in pulp and paper mills. Encapsulated abrasive blasting uses proprietary Sponge-Jet abrasives. The abrasive is mixed with an elastomeric...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003221
EISBN: 978-1-62708-199-3
... various techniques to improve functional surface properties and enhance the appearance of product forms. The article discusses various cleaning and finishing techniques such as abrasive blast cleaning, polishing and buffing, barrel burnishing, chemical cleaning, pickling, etching and bright dipping...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006795
EISBN: 978-1-62708-295-2
... particle erosion. Cavitation erosion is due to the formation and collapse, within a liquid, of cavities or bubbles that contain vapor or gas or both. Liquid impingement erosion is due to impacts by liquid drops or jets. Solid impingement erosion is due to impacts by solid particles. Impingement also...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003832
EISBN: 978-1-62708-183-2
... layers on less resistant substrates. The HVOF process produces coatings with much lower levels of porosity compared to arc and flame spraying. The HVOF spraying process is based on oxyfuel combustion at high pressure inside a spray gun to produce a high-velocity jet. A schematic of the HVOF spray gun is...