Search Results for Wire

This article begins with an overview of steel wire configurations and sizes followed by a discussion on various wiremaking practices. The wiredrawing operation is discussed, including cleaning, die design, use of lubricants and welds, finishes, coating, and thermal treatments. Metallic coatings can be applied to wire by various methods, including hot dip processes, electrolytic process, and metal cladding by rolling metallic strip over the wire. These wires are normally grouped into broad usage categories. These categories, as well as some items in each category, are described in the article under their quality descriptions or commodity names. These include low-carbon steel wire for general usage, wire for structural applications, wire for packaging and container applications, wire for prestressed concrete, wire for electrical or conductor applications, rope wire, mechanical spring wire for general use, wire for fasteners, mechanical spring wire for special applications, upholstery spring construction wire, and alloy wire.

Wire rod is a semifinished product rolled from billet on a rod mill and is used primarily for the manufacture of wire. Steel wire rod is usually cold drawn into wire suitable for further drawing; for cold rolling, cold heading, cold upsetting, cold extrusion, or cold forging; or for hot forging. The article explains these operations, along with the several recognized quality and commodity classifications applicable to steel wire rods. The heat treatments commonly applied to steel wire rod, either before or during processing into wire, include annealing, spheroidize annealing, patenting, and controlled cooling. When the end product must be heat treated, the heat treatment and mechanical properties should be clearly defined. Carbon steel rods are produced in various grades or compositions: low-carbon, medium-low-carbon, medium-high-carbon, and high-carbon steel wire rods. Rod for the manufacture of carbon steel wire is produced with manufacturing controls and inspection procedures intended to ensure the degree of soundness and freedom from injurious surface imperfections necessary for specific applications. This article also describes the various quality descriptors applicable to the rods as well as standard qualities and commodities available in alloy steel wire rod.

This article, with the aid of illustrations and curves, describes an experiment used to understand the cooling characteristics and transformation behavior of steel wires during patenting. The two aqueous polymer quenchants used as alternatives for lead baths, are carboxymethyl cellulose and polyvinyl alcohol. A small amount of polymer additive in spraying could modify the physical properties of the spray medium and improve atomizing status. The concentration-fog flux effect further improves the flexibility of spraying and makes it easier to control the cooling process.

This article describes the operation procedures of wire rolling in a Turks Head machine. It discusses spring coiling, as well as the manual and power bending used in the wire forming process. The article contains a table that lists examples of several wire-forming production problems and solutions. Lubricants for wire forming such as inorganic fillers, soluble oils, and boundary lubricants are reviewed. The article also analyzes the applications of lubricants in wire forming.

Workability is the ability of the workpiece metal to undergo extrusion or drawing without fracture or defect development. This article describes the limits of workability in extrusion and drawing in terms of fracture and flaw development and presents some comments on fracture mechanisms. It discusses the empirical projections of absolute workability from various mechanical tests. The article concludes with a discussion on extrusion and drawing process design implications.

The drawing process, one of the oldest metal forming operations, allows excellent surface finishes and closely controlled dimensions to be obtained in long products that have constant cross sections. This article discusses the basic mechanics and preparation steps of drawing. It presents an overview of the processes, equipment, dies and die materials, and lubrication associated with drawing of rod, wire, bar, and tube. The article also provides a discussion on the design considerations and manufacturing of commercial superconducting multifilamentary conductors.

This article focuses on the cooling process and related transformation behavior of steel wires during patenting to identify a physical metallurgical basis for the development of nontoxic alternatives to molten lead for wire patenting. It describes the materials required, the procedures, and the results of cooling curve analysis. The article schematically summarizes the cooling behaviors of the various cooling media and the microstructure of the pearlite transformation in a lead bath.

This article discusses the mechanics, surface preparation and principles of metal forming operations such as drawing, bending (draw bending, compression bending, roll bending, and stretch bending), spinning, and straightening of bars, tubes, wires, rods and structural shapes. The article also discusses the machines and tools, including dies and mandrels, and lubricants used for these metal forming operations.

Hot-rolled steel bars and other hot rolled steel shapes are produced from ingots, blooms, or billets converted from ingots, or from strand cast blooms and billets, and comprise a variety of sizes and cross sections. This article provides a brief discussion on mechanical properties, quality descriptors and chemical compositions of hot-rolled steel bars, cold-finished steel bars, steel wire rod and steel wire. It contains tables that provide size tolerances for cold-finished carbon steel bar and cold-finished alloy steel bar.

This article provides an overview of the classification system of coppers for conductors and for wires and cables, as well as wire rod fabrication techniques such as rolling and continuous casting. Wiredrawing and wire stranding operations, including the preparation of rod surface, drawing, production of flat rectangular wire, annealing, and coating, are discussed. The article also provides information on electrical insulation and jacketing techniques, including polymeric insulation, enamel insulation, and paper-and-oil insulation.

This article focuses on nondestructive inspection of steel bars. The primary objective in the nondestructive inspection of steel bars and wire is to detect conditions in the material that may be detrimental to the satisfactory end use of the product. The article discusses various types of flaws encountered in the inspection of steel bars, including porosity, inclusions, scabs, cracks, seams, and laps. Inspection methods, such as magnetic-particle inspection. liquid penetrant inspection, ultrasonic inspection, and electromagnetic inspection, of steel bars are also described. The article provides a discussion on electromagnetic systems, eddy-current systems, and magnetic permeability systems for detection of flaws on steel bars. It concludes with a description of nondestructive inspection of steel billets.

Alloy 5056 can be used for nails and for redrawing rod to make wire. This datasheet provides information on key alloy metallurgy, processing effects on physical and mechanical properties, and fabrication characteristics of this 5xxx series alloy.

This article discusses the properties of threaded fasteners made from carbon and low-alloy steels containing a maximum of 0.55% carbon. It provides guidelines for the selection of steels for bolts, studs, and nuts intended for use at temperatures between -50 and 370 deg C. The article also discusses steels rated for service above 370 deg C and describes internationally recognized grade designations. The specifications provided can be used to outline fastener requirements, control manufacturing processes, and establish functional or performance standards. The most commonly used protective metal coatings for ferrous metal fasteners; zinc, cadmium, and aluminum; are described as well.