1-8 of 8 Search Results for

Winches

Sort by
Image
Published: 01 December 2008
Fig. 17 High residual stress and defects encountered in original design (a) were eliminated by redesign (b) of this winch end-plate, sand cast of steel. More
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004139
EISBN: 978-1-62708-184-9
... Abstract This article focuses on the corrosion and deterioration of components on recreational and small workboats. It discusses the materials selection and corrosion control for the components. These components include hulls, fittings, fasteners, metal deck gear, winches, backing plates...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009024
EISBN: 978-1-62708-187-0
... of metal at each junction. Fig. 17 High residual stress and defects encountered in original design (a) were eliminated by redesign (b) of this winch end-plate, sand cast of steel. A redesign that replaced the opposing ribs with radial corrugations is shown in Fig. 17(b) . These corrugations...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003407
EISBN: 978-1-62708-195-5
... used only in the high-traffic areas, such as the cockpit. With skin thickness of 1.8 mm (0.07 in.) outside and 1.1 mm (0.04 in.) inside, there is a requirement for considerable local reinforcement in the region of fittings, such as winches and sail tracks. Overall, an average panel weight of less than...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003482
EISBN: 978-1-62708-195-5
..., ranging from difficulty in placement to concerns related to overall durability and corrosion resistance. Steel plates are heavy and unwieldy and thus difficult to handle during erection. At the minimum, jacks, extensive scaffolding, and winches or cranes are needed. The length of individual plates...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004138
EISBN: 978-1-62708-184-9
... corrosion of: Hulls, fittings, and fastenings Metal deck gear Equipment such as winches, lifeline supports, and anchor systems Propulsion systems Electrical and electronic systems Plumbing systems Masts, spars, and rigging Corrosion of Firearms Corrosion has been the main...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005107
EISBN: 978-1-62708-186-3
...) Metal fabrication shops Aircraft manufacturers (titanium, Inconel, stacked metals) Heavy equipment manufacturers (tractors, hoists, cranes, industrial winches, derricks) Industrial vehicles (trucks, tankers, construction vehicles) Structural fabrications (bridges, skyscrapers) and heavy...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005135
EISBN: 978-1-62708-186-3
... form for the desired radius is bolted to the bending table. Steel pins or stops can be placed in the holes in the table to keep the work in line. A clamshell furnace in sections is the usual source of heat. Winches, jacks, and hoists supply the bending force. A typical application is described...