1-20 of 1398 Search Results for

Sulfurization

Sort by
Image
Published: 31 December 2017
Fig. 8 Synthesis of sulfur extreme-pressure agents. (a) Olefin sulfurization. (b) Dithiocarbamic acid derivatives More
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004178
EISBN: 978-1-62708-184-9
... Abstract This article describes the selection of materials for the production and handling equipment of concentrated sulfuric acid, depending on factors such as the allowable corrosion rate, desired mechanical and physical properties, fabrication requirements, availability, and cost. Materials...
Series: ASM Handbook
Volume: 3
Publisher: ASM International
Published: 27 April 2016
DOI: 10.31399/asm.hb.v03.a0006201
EISBN: 978-1-62708-163-4
... Abstract This article is a compilation of binary alloy phase diagrams for which sulfur (S) is the first named element in the binary pair. The diagrams are presented with element compositions in weight percent. The atomic percent compositions are given in a secondary scale. For each binary...
Image
Published: 01 January 2003
Fig. 3 The sulfur cycle showing the role of bacteria in oxidizing elemental sulfur to sulfate ( SO 4 2 − ) and in reducing sulfate to sulfide (S 2− ). Source: Ref 12 More
Image
Published: 31 August 2017
Fig. 15 Estimate of free sulfur content as a function of manganese and sulfur concentrations. Source: Ref 13 More
Image
Published: 01 October 2014
Fig. 17 Influence of sulfur contents on microstructure of DHT steels. (a) 0.09% S. (b) 0.054% S. Source: Ref 25 with permission from the Society of Automotive Engineers of Japan, Inc. More
Image
Published: 01 January 1990
Fig. 10 Average high-temperature sulfur corrosion rates in a hydrogen-free environment compiled from an American Petroleum Institute survey. Source: Ref 19 More
Image
Published: 30 September 2015
Fig. 23 Effect of sulfur and carbon on the ultimate tensile strength of iron-copper-carbon alloys. Samples were upset forged and forced-air cooled. More
Image
Published: 30 September 2015
Fig. 3 Polarization curve for a stainless steel in a sulfuric acid solution. E t , transpassive potential; E p , pitting potential; E pp , primary passivation potential; E corr , corrosion potential; i p , passive current density. Source: Ref 3 More
Image
Published: 31 October 2011
Fig. 7 Plot of weld d / w ratio versus sulfur content for approximately 200 heats of type 304L stainless steel. Each point is an average of multiple sulfur analyses and weld d / w ratio measurements. If single values are used, the scatter is greater. Source: Ref 11 More
Image
Published: 01 January 1990
Fig. 3 Optimum range of initial sulfur level as a function of type (figure) and amount (table) of minor elements used for graphite compaction. The above table shows the sulfur range, Δ S , for compacted iron formation with different spheroidizers in an iron composition of 3.5% C, 2.1% Si, 0.75 More
Image
Published: 01 January 1990
Fig. 20 Effect of cerium-to-sulfur ratio on upper-shelf impact energy for HSLA steel. Circles, steel treated with mischmetal; squares, steel treated with rare-earth silicides More
Image
Published: 01 January 1990
Fig. 30 Effect of sulfur content on corrosion rates predicted by modified McConomy curves in the temperature range of 290 to 400 °C (550 to 750 °F). Source: Ref 39 More
Image
Published: 01 January 1990
Fig. 5 Influence of sulfur on the transition temperature of purified iron containing 2000 ppm O, and the influence of carbon content on sulfur embrittlement. Increasing carbon content has the beneficial effect of decreasing sulfur embrittlement. Source: Ref 9 , 10 More
Image
Published: 01 January 1990
Fig. 6 Influence of sulfur, tellurium, and selenium on the transition temperature of purified iron containing up to 10 ppm carbon and approximately 2000 ppm O. Source: Ref 10 More
Image
Published: 01 January 1990
Fig. 14 Effect of sulfur content on transverse impact energy at room temperature in a silicon-aluminum-killed steel More
Image
Published: 01 January 1986
Fig. 26 Histograms indicating the coverage and distribution of sulfur on intergranular fracture surfaces of vacuum-melted nickel for two heat treatments. More
Image
Published: 01 January 1986
Fig. 28 Effect of sulfur grain-boundary coverage on the fracture mode and ductility. More
Image
Published: 01 January 1986
Fig. 33 Surface distribution of sulfur and phosphorus after heating a 304 stainless steel sample at 750 °C (1380 °F). More
Image
Published: 01 January 2005
Fig. 24 Effect of sulfur and carbon on the ultimate tensile strength of iron-copper-carbon alloys. Samples were upset forged and forced-air cooled. More