1-20 of 433 Search Results for

Stampings

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 1994
Fig. 2 Rack used for cleaning and phosphate coating small stampings More
Image
Published: 01 January 2006
Fig. 23 Lift-and-carry transfer device for stampings More
Image
Published: 30 August 2021
Fig. 33 Axle journal end stampings. Clockwise: manufacturer’s marks (MRF, McKees Rocks Forgings; date of manufacture, June 1990), heat number, and serial number. The bearing components were degreased and cleaned in solvent. Beyond typical fretting wear seen in the ridges worn into the inner More
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003019
EISBN: 978-1-62708-200-6
..., resulting in higher surface quality and less tendency for the occurrence of subsequent defects during painting. Molding and Tooling In the process of loading the material into a compression or stamping tool, the charge of material to be molded is somewhat smaller in length and width but is thicker...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0009000
EISBN: 978-1-62708-186-3
... coating, applicable to both mild steel and high-strength steels stampings. The article discusses the behavior of the surface conditions through quantitative measurements and surface analyses conducted throughout the wear tests. The surface conditions include surface roughness, surface morphology...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0009001
EISBN: 978-1-62708-186-3
... of the die surfaces. In stamping operations of sheet metals for automotive body-in-white (BIW) parts, automotive original equipment manufacturers (OEMs) have been concerned about stamping advanced high-strength steels (AHSS) and ultrahigh-strength steels because extremely high contact pressure and heat...
Image
Published: 01 January 1990
Fig. 22 CPM 10V punch and copper-beryllium blank used in a progressive stamping operation. Courtesy of Crucible Materials Corporation More
Image
Published: 01 January 2002
Fig. 17 Wiper spring that fractured at a small-radius corner of a stamped bend. (a) Configuration and dimensions (given in inches) of the spring. (b) SEM micrograph showing a forming crack (arrow) in the 135° corner on a new spring. 200×. (c) SEM micrograph showing a crack (arrow More
Image
Published: 01 January 2002
Fig. 14 A quench crack promoted by the presence of a deep, sharp stamp mark in a die made of AISI S7 tool steel. This die had not been tempered, or was ineffectively tempered, after hardening. 2× More
Image
Published: 01 January 2006
Fig. 7 CPM 10V punch and copper-beryllium blank used in a progressive stamping operation. Courtesy of Crucible Materials Corporation More
Image
Published: 01 January 2006
Fig. 2 Method for stacking laminations stamped in individual dies More
Image
Published: 01 January 2006
Fig. 1 Stamping press More
Image
Published: 01 December 1998
Fig. 57 Two operations that simulate stamping: (a) deep drawing and (b) stretching More
Image
Published: 01 January 2006
Fig. 7 Example of measured strains on a complex stamping. These strains are plotted on the forming limit diagram in Fig. 4 , which was drawn assuming an n -value of 0.24 and a thickness of 0.90 mm (0.035 in.). e ma , major strain; e mi , minor strain. Dimensions given in inches More
Image
Published: 01 January 2006
Fig. 10 The basic steps in the creation of a stamped sheet metal part for an automobile. The steps shown are those where formability issues must be addressed in one form or another. More
Image
Published: 01 January 2006
Fig. 4 Reduction in lead time for simulating the stamping of an automotive panel More
Image
Published: 01 January 2006
Fig. 30 Flow chart of die tryout with stamping computer-aided engineering (CAE) simulation More
Image
Published: 01 January 2006
Fig. 10 Control chart of average thickness ratio t f / t 0 for a stamping, where t f is final thickness, and t 0 is initial thickness. Note the increase in forming severity (reduced thickness ratio) beginning at week 21 and the continuous decrease in thickness ratio beginning at week More
Image
Published: 01 January 1997
Fig. 37 Flat-bottomed pan stamped from 2008-T4 aluminum sheet showing wrinkling on the flange. Source: Ref 27 More
Image
Published: 01 January 2006
Fig. 44 Heated die system for warm stamping of aluminum alloys. (a) Schematic diagram of warm forming dies. (b) Schematic of formed sheet part. (c) Chrysler Neon door inner panel successfully formed at 350 °C (660 °F) using aluminum 5182 plus manganese sheet More