1-20 of 225 Search Results for

Saw blades

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 1989
Fig. 4 Standard tooth forms for steel and carbidetip bond saw blades More
Image
Published: 01 January 1989
Fig. 6 Set patterns for saw blades More
Image
Published: 31 October 2011
Fig. 6 Flash-welding machine installation equipped to weld band-saw blades More
Image
Published: 01 January 1993
Fig. 11 Basic tooth forms used in band saw blades More
Image
Published: 01 January 1993
Fig. 4 Flash-welding machine installation equipped to weld band-saw blades More
Image
Published: 01 January 1989
Fig. 5 Standard nomenclature for saw blade teeth. More
Image
Published: 01 January 1993
Fig. 10 Schematic showing the key elements of a band saw blade cutting edge More
Series: ASM Handbook
Volume: 12
Publisher: ASM International
Published: 01 January 1987
DOI: 10.31399/asm.hb.v12.a0000613
EISBN: 978-1-62708-181-8
...-overload fractures, impact fractures, microstructure, quench cracking, brittle-in-service failure, hydrogen embrittlement, stress-corrosion cracking, and grain-boundary cracking of tool steel components. These components include diesel engine injector plungers, rivet-heading tools, circular saw blades...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001366
EISBN: 978-1-62708-173-3
...-welding applications, including chain links, transmission bands, automotive flywheel ring gears, aircraft landing gear, band-saw blades, and crankshaft counter weights. It describes the components of a typical flash-welding machine. The article provides information on the electrical controls of flash...
Image
Published: 01 January 1990
) range. (c) Synthesized diamond grains for use in diamond saw blade applications, such as for the sawing of marble, granite, and concrete. These grains are in the 20 to 60 mesh size (850 to 250 μm) range. More
Image
Published: 15 January 2021
Fig. 10 Surface residual-stress map of resistance-welded, heat-treated, and ground steel saw blade. Source: Ref 39 More
Image
Published: 01 January 2002
Fig. 10 Surface residual-stress map of resistance welded, heat treated, and ground steel saw blade. Source: Ref 30 More
Book Chapter

By Ted A. Slezak
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002146
EISBN: 978-1-62708-188-7
... and materials, blade design, and cutting fluids associated with the band sawing process. The article also discusses the variables considered in band saw machining. In addition, it presents examples representing the comparison of contour band sawing with milling and shaping in various applications. The article...
Image
Published: 01 December 2004
Fig. 7 A carbon fiber composite with a titanium fastener is clamped in a fixture and aligned for sectioning. In this figure, the alignment is performed using a straight edge. This sample will be sectioned through the fastener, with the straight edge providing alignment of the edge of the saw More
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001486
EISBN: 978-1-62708-173-3
... and one idle. The cutting tool is a welded continuous loop of flexible saw blade carried in one direction around the wheels and through the workpiece. This configuration permits full utilization of a cutting tool with hundreds of cutting edges, or teeth ( Fig. 10 ). The band saw blade is thinner than...
Book Chapter

Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005174
EISBN: 978-1-62708-186-3
... cutting action produces even wear over the entire length of the saw band. The blades for band saws are also changed less frequently, because they are longer than the blades in other types of saws. Band saws can be used to cut contours or straight lines, depending on the type of machine. Most band saws...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002188
EISBN: 978-1-62708-188-7
... Nickel alloys can be sawed or cut off by conventional methods. Hacksawing Hand and power hacksaws are suitable for cutoff operations involving the alloys of groups A, B, C, and D-1. Alloys of group D-2 are not readily cut by these tools. Hand hacksaw blades should be made of high-speed steel...
Series: ASM Handbook
Volume: 9
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.hb.v09.a0003746
EISBN: 978-1-62708-177-1
... of the presence of residual stresses that often tend to close the newly created surfaces toward each other, thus pinching the blade. This can be a particular problem (saw blade damage) as the last bit of the cut is made. Some hints for dealing with this situation are provided later in this article. It is also...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005178
EISBN: 978-1-62708-186-3
... and Production Practice” in this article. Angles are usually sheared in a special machine or in a special setup with conforming blades. Because of the conditions illustrated in Fig. 1 , the edges sheared with straight blades are not as high quality as edges that are sawed or otherwise machined. However...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002194
EISBN: 978-1-62708-188-7
... material, including metals. Trimming is one of the more common operations in the fabrication of composite materials (both MMCs and resin-matrix composites). The cutting tools used include circular saws, router cutters, and abrasive tools. For straight-line cuts, diamond-coated circular saw blades...