1-20 of 517 Search Results for

Rusting

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001276
EISBN: 978-1-62708-170-2
... Abstract Rust-preventive compounds are removable coatings used for the protection of the surfaces of iron, steel, coated or galvanized products, and other alloys. This article describes the basic parts of rust-preventive compounds, namely, carrier, film former, polar materials, and specialty...
Image
Published: 30 September 2015
Fig. 14 (a) Bolted splice plate with heavy rusting on bolt heads, edges, and in crevices, all difficult areas to coat. (b) Rusted rivet heads and bolts on an old truss bridge. These irregular surfaces are difficult to paint thoroughly. Courtesy of KTA-Tator, Inc. More
Image
Published: 01 December 1998
Fig. 1 Service life (time to 5% rusting of steel surface) versus thickness of zinc for selected atmospheres. Shaded area is thickness range based on minimum thicknesses for all grades, classes, etc., encompassed by ASTM A 123 and A 153. Source: Ref 1 Atmosphere Description Heavy More
Image
Published: 01 January 1994
Fig. 2 Service life (time to 5% rusting of steel surface) versus thickness of zinc for selected atmospheres. Shaded area is thickness range based on minimum thicknesses for all grades, classes, etc., encompassed by ASTM A 123 and A 153. Source: Ref 2 Atmosphere Description Heavy More
Image
Published: 01 January 2005
Fig. 3 The owner complained about the serious rusting and perforation to the rear of his 4 by 4 vehicle after approximately 2 years of use. Subsequent review revealed that the vehicle was used to tow and launch a boat directly into the ocean each weekend during the spring, summer, and fall More
Image
Published: 01 January 2005
Fig. 14 Martensitic stainless steel pitchforks were rusting before they left the storeroom; paint was blistering, and the product was unappealing. The cause was due to incorrect surface preparation compounded by poor storage conditions. The forks were hot forged and quenched to obtain More
Image
Published: 01 January 2005
Fig. 16 The upper area of an aboveground storage tank displayed local rusting and loss of paint coating, primarily because it could not be drained. The tank was located directly under an apple tree, which contributed to further impacts as fruit fell and was left undisturbed on the coated steel More
Image
Published: 01 January 2006
Fig. 3 Rusting on a phosphated part after service in a desert environment. The phosphate coating had been blasted off by blowing sand leaving a bare metal surface. Phosphate coatings are specified on 75 to 90% of the parts for small arms. More
Image
Published: 01 January 2005
Fig. 14 Period to failure (appearance of rusting on the coating surface) for high-velocity oxyfuel (HVOF)-sprayed Hastelloy C coatings on a steel substrate. The HVOF denotes a commercial HVOF; heat treatment was carried out in vacuum at 1050 °C (1920 °F) for 1 h. More
Image
Published: 01 January 1997
Fig. 1 Service life (time to 5% rusting of steel surface) versus thickness of zinc for selected atmospheres. Shaded area is thickness range based on minimum thicknesses for all grades, classes, and so forth, encompassed by ASTM A 123 and A 153. Source: Ref 10 More
Image
Published: 30 September 2015
Fig. 7 Stratified rust/rust scale More
Image
Published: 30 September 2015
Fig. 16 (a) Pack rust between two plates. (b) Stratified rust on the top of a steel flange. Courtesy of KTA-Tator, Inc. More
Image
Published: 01 January 2005
Fig. 2 Dependence of rust particle flake size on the chloride content in the rust. Source: Ref 13 More
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003697
EISBN: 978-1-62708-182-5
... of iron and steel in soil Table 3 Potentials of iron and steel in soil Metal Potential (a) , mV Mild steel (clean and shiny) −500 to −800 Mild steel (rusted) −200 to −500 Cast iron (not graphitized) −500 High-silicon cast iron −200 Mill scale on steel −200...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004121
EISBN: 978-1-62708-184-9
..., or peeling. This entire tank was then repainted with one of the moisture-cured polyurethane systems. The coating exhibited no evidence of cracking or peeling, no evidence of rust, and no evidence of corrosion for the past 4 years ( Ref 10 ). Fig. 12 Deluge tank (for fire-suppression system) with test...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004109
EISBN: 978-1-62708-184-9
Image
Published: 30 September 2015
Fig. 7 Positive ferrous ions react with negative hydroxide ions, forming rust and resulting in pits. Source: Ref 17 More
Image
Published: 30 September 2015
Fig. 31 Fine spots of rust that appear on a paint film, often a thin primer coat. The initial spots rapidly spread over the surface, resulting in a film of rust through which the individual spots are difficult to discern. Also from holidays More
Image
Published: 30 September 2015
Fig. 32 Individual spots of rust that appear on a paint film and frequently start as localized spotting but rapidly increase in density More
Image
Published: 01 January 1990
Fig. 8 Rust versus nickel content from 200 h neutral salt spray at 35 °C (95 °F) More