1-20 of 689 Search Results for

Rollers

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002138
EISBN: 978-1-62708-188-7
... Abstract Roller burnishing is a method of working a metal surface to improve its finish and dimensional accuracy and can provide some degree of work hardening. This article discusses the workpiece requirements used for roller burnishing. It illustrates the types of roller burnishing tools...
Image
Published: 09 June 2014
Fig. 3 Induction heating coil for hardening of undercarriage rollers. Source: Ref 1 More
Image
Published: 09 June 2014
Fig. 4 Immersion quench system for undercarriage rollers. Source: Ref 1 More
Image
Published: 01 January 1989
Fig. 29 Box tool with rollers for support of the workpiece during axial turning More
Image
Published: 01 January 1989
Fig. 19 Setup for end lapping large quantities of hardened steel rollers More
Image
Published: 01 January 2006
Fig. 13 Diagrams of typical forming rollers used for spinning of cones and hemispheres. (a) Full-radius roller. (b) Roller profiled for forming corners. (c) Roller used for reducing the wall thickness. Dimensions given in inches More
Image
Published: 01 December 1998
Fig. 12 Large-radius rollers staggered radially for forward spinning of tube, showing how each roller takes a portion of the total bite ( X ) More
Image
Published: 01 January 2002
Fig. 11 Denting damage to cone, cup, and rollers from debris entering the bearing from spalling in another component, through defective seals, or from improperly cleaned housings. More
Image
Published: 31 August 2017
Fig. 39 High-chromium (ASTM II-D) coal-crushing replacement rollers. The inside bearing races have been machined and are ready for field installation. More
Image
Published: 01 January 2001
Fig. 24 Schematic diagram of cutting with feed rollers. (a) Rubber roller. (b) Hub. (c) Feed roller. (d) Fiber. (e) Tensioning roller. (f) Cutting roller. (g) Cutting edge. (h) Cut fibers More
Image
Published: 01 January 2001
Fig. 20 Fracture feature known as matrix rollers on the surface of a carbon/KIII thermoplastic composite, following failure under mode II shear loading conditions. 1000× More
Image
Published: 30 August 2021
Fig. 20 Sketch of sugar mill roller. (a) Three rollers of sugar mill placed in triangular formation. (b) Direction of maximum force acting on top roller More
Image
Published: 30 August 2021
Fig. 48 Water etching present on rollers More
Image
Published: 01 January 1996
Fig. 1 Scanning electron micrograph of a fatigue spall on a roller from a roller bearing after 630,000 cycles. Roller is AISI 1060 steel, hardened to 600 HV. Spall is 400 μm wide by 700 μm long. More
Image
Published: 31 December 2017
Fig. 5 Crowned roller geometry used in radial roller bearings. (a) Fully crowned (spherical roller). (b) Partially crowned (cylindrical roller). I , r oller length; D , roller diameter; R , crown radius More
Image
Published: 31 December 2017
Fig. 7 Schematics of thrust roller bearings. (a) Thrust cylindrical roller bearing limited to use with axial loads only, due to its 90° contact angle. (b) Spherical roller thrust bearing, which incorporates asymmetrical rollers that tolerate a misalignment ranging from ±1 to ±3, depending More
Image
Published: 30 September 2015
Fig. 34 Raw material utilization in the production of a tapered roller bearing race. (a) Produced from hot rolled tube stock. (b) Powder forged from preform. Source: Ref 112 More
Image
Published: 09 June 2014
Fig. 6 (a) Vibratory bowl feeder. (b) Vibratory bowl feeder roller track. (c) Inclined roller track More