1-20 of 73 Search Results for

Drilling rigs

Sort by
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006698
EISBN: 978-1-62708-210-5
... Other (each) 0.05 max Other (total) 0.15 max Al bal Properties of alloy 5086 are given in Tables 2 to 4 . Product specifications are listed in Table 5 . Typical applications are marine, automotive, and aircraft parts; cryogenics; television towers; drilling rigs; transportation...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006697
EISBN: 978-1-62708-210-5
... in Tables 2 to 5 . Typical uses are marine, auto, and aircraft applications; unfired welded pressure vessels; cryogenics; television towers; drilling rigs; transportation equipment; missile components; and armor plate. In the cold rolled H131 temper, the alloy is commonly used for military armor plate...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003433
EISBN: 978-1-62708-195-5
... be correct and within tolerance. If an optical reference system is used, it must be verified, and the date of optical equipment calibration must be checked. Rigging: The rigging should be checked to verify that the rigged templates are located properly and are vertical (not bowed or twisted). Faired...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009014
EISBN: 978-1-62708-187-0
.... permanent mold aluminum casting casting simulation sand mold aluminum casting casting design cost drivers structured team approach shape optimization rigging system design DESIGN is the critical first step in the development of cost effective, high quality castings. Designing a successful...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003096
EISBN: 978-1-62708-199-3
... of 150, 200, 300, 350, and 400 mm (6, 8, 12, 14, and 16 in.) in outside diameter. Driven well pipe is threaded pipe in short lengths used for the manual driving of a drill tool or for use with short rigs. It may be furnished in random lengths ranging from 0.9 to 1.8 m (3 to 6 ft) or in random lengths...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004139
EISBN: 978-1-62708-184-9
..., lifeline supports, inboard engines, cooling systems, propulsion systems, electrical and electronic systems, plumbing systems, masts, spars, and rigging. recreational boats corrosion corrosion control metal deck gear electrical and electronic systems fasteners materials selection small...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003481
EISBN: 978-1-62708-195-5
... Abstract This article provides information on the potential applications of fiber-reinforced polymer (FRP) composites for maritime craft and offshore drilling platforms. The key benefits gained from using FRP materials together with an examination of the drawbacks and major issues impeding...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003565
EISBN: 978-1-62708-180-1
... pressure and ultimately engine failure. Failure of tools used for drilling rock and other media raises cost concerns associated not only with the need for frequent replacement of parts, but also with the down time incurred. Impact wear of printer typefaces will lead to loss of definition and a subsequent...
Series: ASM Handbook
Volume: 24A
Publisher: ASM International
Published: 30 June 2023
DOI: 10.31399/asm.hb.v24A.a0006958
EISBN: 978-1-62708-439-0
... oil wells were drilled in China in the 4th century A.D. ( Ref 3 ). Today (2022), the technology used by the O&G industry is rivaling that of space exploration and is highly sophisticated. For example, to drill a complex-trajectory, ~15 km (9 miles) long well, landing at the precise spot where...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006430
EISBN: 978-1-62708-192-4
... of nuclear power plants. MCSA has a variety of sources, with the more accepted developments being related to the University of Edinburgh for testing off-shore drilling rig electric motors. The development of both technologies trace back to the late 1970s, with commercial applications after 1980...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006793
EISBN: 978-1-62708-295-2
... and safety, reliability, and quality can be greatly reduced. Excessive wear from inlet and exhaust valves impacting their seating faces in automotive engines can lead to loss of cylinder pressure and ultimately engine failure. Failure of tools used for drilling rock and other media raises cost concerns...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003285
EISBN: 978-1-62708-176-4
... small amplitude. The article also reviews the fretting rig for investigating fretting wear. sliding contact surface damage statistical analysis adhesive wear galling testing button-on-block galling test pin-on-flat galling test threaded connection galling test fretting wear profilometry...
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.a0005735
EISBN: 978-1-62708-171-9
... Abstract This article focuses on noble and neutral coatings and the requirements necessary to achieve successful industrial applications. These include corrosion and wear control and repair applications in processing and chemical industries, and valve and downhole drilling applications...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009018
EISBN: 978-1-62708-187-0
... the cored hole, Fig. 7(b) . The hole could be drilled later, increasing the cost of machining but saving the cost of coring. The relative economy of coring and not coring can be determined only by analysis of the total cost of finished parts produced by each method. Several examples are given in the next...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004210
EISBN: 978-1-62708-184-9
... is also responsible for the external corrosion of offshore platforms and drilling rigs. In oil and gas production, highly stressed structural members are directly exposed to a corrosive, aerated seawater environment. This also makes localized corrosion and corrosion fatigue a particular concern...
Series: ASM Handbook
Volume: 1
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v01.a0001020
EISBN: 978-1-62708-161-0
... well pipe is threaded pipe in short lengths used for the manual driving of a drill tool or for use with short rigs. It may be furnished in random lengths ranging from 0.9 to 1.8 m (3 to 6 ft) or in random lengths ranging from 1.8 to 3.0 m (6 to 10 ft). Casing is used both to confine and conduct...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002395
EISBN: 978-1-62708-193-1
... of corrosion fatigue crack initiation and prevention of corrosion fatigue. It presents case histories of fatigue failure of various steel components. The article reviews the failure of coiled tubing in a drilling application and the failure of coiled tubing due to hydrogen sulfide exposure, with examples...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006386
EISBN: 978-1-62708-192-4
... environment for seed germination, root growth, soil erosion control, and moisture control. There are several implements used for primary tillage, secondary tillage, and seed drills based on soil condition, crop, and farming practices ( Ref 7 ). Primary tillage equipment is used to break soil below the ground...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003403
EISBN: 978-1-62708-195-5
... edge-guard material around the periphery of the tool laminate can protect the edge from minor impacts in production, such as contact with belt buckles. Molded index fingers or locator buttons can be included in the design to provide accurate location for subsequent trimming, drilling, or assembly...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009023
EISBN: 978-1-62708-187-0
... the amount of padding required, several castings were produced with a standard, straight-through core that allowed 1 8 in. of additional metal on the inside diameter of the casting for machining stock. The castings were rigged with a large riser at the top and a side riser (also serving...