1-20 of 79 Search Results for

Crushers

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 2002
Fig. 18 Failure of a ductile iron cone-crusher frame ( example 7 ). (a) Near-surface microstructure of the frame showing degenerate graphite morphology rather than the intended nodular structure evident in the core. Unetched. 30×. (b) The typical frame microstructure also exhibits high levels More
Image
Published: 01 December 1998
Fig. 5 Relative wear ratios of ferrous alloys in jaw crusher tests More
Image
Published: 01 January 1990
Fig. 17 Relative wear ratios of ferrous alloys in jaw crusher tests. Source: Ref 7 More
Image
Published: 31 December 2017
Fig. 7 Worn cone crusher liner after three months of use More
Image
Published: 31 December 2017
Fig. 27 Relative wear ratios of ferrous alloys in jaw crusher tests. Source: Ref 20 More
Image
Published: 01 January 2000
Fig. 9 Schematic diagram of jaw crusher wear apparatus. Source: Ref 47 , 49 More
Image
Published: 01 January 2002
Fig. 3 Worn cone crusher liner after three months of use More
Image
Published: 15 January 2021
Fig. 14 Failure of a ductile iron cone-crusher frame (Example 7). (a) Near-surface microstructure of the frame showing degenerate graphite morphology rather than the intended nodular structure evident in the core. Unetched. Original magnification: 30×. (b) The typical frame microstructure also More
Image
Published: 31 December 2017
Fig. 3 (a) The truck bed is abraded by the free flow of dumped ore or minerals under relatively low wearing stress. (b) Abrasive wear of tractors during the process of plowing soil under low wearing stress. (c) Wear of ore crushers (roller crusher) under high stresses More
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003169
EISBN: 978-1-62708-199-3
... Abstract Ores, which consist of the primary valuable mineral, predominant gangue content, valuable by-products, and detrimental impurities, are extracted and directed to mineral processing. This article describes the mineral processing facilities, such as crushers, grinders, concentrators...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003090
EISBN: 978-1-62708-199-3
... pearlitic microstructure; the machine housing has a ferrite plus pearlite matrix with graphite flakes; and the jaw crusher microstructure contains martensite and cementite. cast irons material selection mechanical properties microstructure steels THE PROPERTIES of irons and steels are linked...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003560
EISBN: 978-1-62708-180-1
... crusher wear, electronic circuit board drill wear, grinding plate wear failure analysis, impact wear of disk cutters, and identification of abrasive wear modes in martensitic steels. abrasive wear failures abrasive wear mechanisms adhesive wear erosive-type wear wear failure analysis...
Series: ASM Handbook
Volume: 1
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v01.a0001045
EISBN: 978-1-62708-161-0
... Abstract This article discusses the composition, processing, and properties of austenitic manganese steel. Austenitic manganese steel is used in equipment for handling and processing earthen materials, such as rock crushers, grinding mills, dredge buckets, power shovel buckets and teeth...
Image
Published: 01 January 2002
Fig. 14 Photograph of the movable (top) and stationary (bottom) wear plates from the jaw crusher. The feed moves across the plates from left to right, so the most severe wear occurs at the exit area toward the right. More
Image
Published: 15 January 2021
Fig. 14 Photograph of the movable (top) and stationary (bottom) wear plates from the jaw crusher. The feed moves across the plates from left to right, so the most severe wear occurs at the exit area toward the right. More
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003283
EISBN: 978-1-62708-176-4
... of equipment, such as bulldozer blades, excavator teeth, rock drill bits, crushers, slushers, ball mills and rod mills, chutes, slurry pumps, and cyclones. Figure 1 shows the extent of abrasion that can occur on a bulldozer blade. However, abrasive wear is not limited to these activities. Abrasion...
Book Chapter

Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006790
EISBN: 978-1-62708-295-2
... abrasion also occurs in impact crushers or almost anywhere where coarse rocks impact a metal surface under considerable pressure or force, for example, digger teeth on power shovels and dragline buckets used to scoop up loose rock. Gouging abrasion normally occurs in the crushing and handling of large...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003102
EISBN: 978-1-62708-199-3
..., mining, quarrying, oil well drilling, steelmaking, railroading, dredging, lumbering, cement manufacture, and clay production. Austenitic manganese steel is used in equipment for handling and processing earthen materials (such as rock crushers, grinding mills, dredge buckets, power shovel buckets...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001302
EISBN: 978-1-62708-170-2
... Practice for Conducting Dry Sand/Rubber Wheel Abrasion Test,” G 65, ASTM 10. “Standard Test Method for Wear Testing with a Crossed-Cylinder Apparatus,” G 83, ASTM 11. “Standard Practice for Jaw Crusher Gouging Abrasion Test,” G 81, ASTM 12. “Test Method for Abrasion Resistance...
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.a0005712
EISBN: 978-1-62708-171-9
... to grow to approximately 4 million barrels of oil per day by 2020 ( Ref 3 ). The oil sands currently are processed primarily by surface mining. A schematic of the open pit process is shown in Fig. 1 . Oil sand deposits are removed via truck and shovel operations and transported via a crusher/conveyor...