1-20 of 45 Search Results for

CF-8M

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 2006
Fig. 4 Pitting corrosion of an ACI CF-8M stainless steel pump case used to pump a nickel plating solution with a high concentration of Cl − and a high operating temperature. This damage occurred during 3 years of service. Courtesy of A.R. Wilfley & Sons, Inc., Pump Division More
Image
Published: 01 January 2006
Fig. 5 Crevice corrosion at the intake flange of an ACI CF-8M stainless steel pump case. Notice that the corrosion damage occurred under the gasket. Courtesy of A.R. Wilfley & Sons, Inc., Pump Division More
Image
Published: 01 December 2004
Fig. 27 Ferrite in CF-8M stainless steel in the (a) as-cast condition and (b) after solution annealing. Revealed using glyceregia More
Image
Published: 01 January 1993
Fig. 3 Varestraint test results on several heats of CF-8M corrosion-resistant alloy. Tests were run at 1 2 % augmented strain using an energy input of approximately 2.7 kJ/mm (69 kJ/in.). See Table 3 for heat number chemical compositions. More
Image
Published: 01 December 2008
Fig. 1 Two applications of Replicast steel parts. (a) CF-8M stainless steel 150 mm (6 in.) butterfly valve body. The part is approximately 305 mm (12 in.) in outside diameter, 64 mm (2 1 2 in.) thick, and weighs 11 kg (25 lb). Note as-cast bolt holes and O-ring groove. (b) 8640 steel More
Image
Published: 01 August 2018
Fig. 13 Cast CF-8M stainless steel impeller that required three different viewing directions and nine separate shots to provide complete coverage in radiographic inspection. Dimensions given in inches More
Image
Published: 01 January 2002
Fig. 11 The classic appearance of erosion-corrosion in a CF-8M pump impeller More
Image
Published: 15 January 2021
Fig. 11 Classic appearance of erosion-corrosion in a CF-8M (cast equivalent of wrought AISI 316 stainless steel) pump impeller More
Image
Published: 01 January 1990
Fig. 5 Yield strength and tensile strength versus percentage of ferrite for CF-8 and CF-8M alloys. Curves are mean values for 277 heats of CF-8 and 62 heats of CF-8M. Source: Ref 3 More
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004179
EISBN: 978-1-62708-184-9
... seals Heaters Coolers <40 Ambient 304L 304L NA NA PE/PP/Fe CF-8M CF-8M PTFE/SS 310 (sp) 304L CF-8 PVDC/Fe PE/PP 52 (125) to BP 304L 304L Alloy 20 304L 304L CF-8M CF-8M PTFE/SS 316L 310 (sp) 310 (sp) Alloy 20 PTFE/Fe CD-4MCu CF-3M PTFE >BP NA 304L...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003813
EISBN: 978-1-62708-183-2
... corrosion oxidation stress corrosion sulfidation corrosion-resistant stainless steels CAST STAINLESS STEELS are usually specified on the basis of composition by using the alloy designation system established by the Alloy Casting Institute (ACI). The ACI designations, such as CF-8M, have been...
Image
Published: 01 January 1990
-20 WQ from above 1095 °C (2000 °F) CF-8M, CF-12M WQ from 1065–1150 °C (1950–2100 °F) CF-8C WQ from 1065–1120 °C (1950–2050 °F) CF-16F WQ from above 1095 °C (2000 °F) CH-20 WQ from above 1095 °C (2000 °F) CK-20 WQ from above 1150 ° (2100 °F) CN-7M WQ from above 1065–1120 °C More
Series: ASM Handbook
Volume: 1
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v01.a0001047
EISBN: 978-1-62708-161-0
... following the first two letters indicate maximum carbon content (percentage × 100) of the alloy. Finally, if further alloying elements are present, these are indicated by the addition of one or more letters as a suffix. Thus, the designation of CF-8M refers to an alloy for corrosion-resistant service (C...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001413
EISBN: 978-1-62708-173-3
... of ± 0.05 wt%. Finally, if further alloying elements are present, these are indicated by the addition of one or more letters as a suffix. Thus, the designation of CF-8M refers to an alloy for corrosion-resistant service (C) of the 19Cr-9Ni type with a maximum carbon content of 0.08% that contains molybdenum...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003118
EISBN: 978-1-62708-199-3
... content (percentage × 100) of the alloy. Finally, if further alloying elements are present, these are indicated by the addition of one or more letters as a suffix. Thus, the designation of CF-8M refers to an alloy for corrosion-resistant service (C) of the 19Cr-9Ni type ( Fig. 1 ), with a maximum carbon...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004183
EISBN: 978-1-62708-184-9
... version Corrosion rate mm/yr mils/yr ACI CF-8M Type 316 0.79 31 ACI CN-7M … 1.04 41 ACI CD-4MCu Duplex stainless steel 1.24 49 ACI CW-12M Hastelloy C 0.056 2.2 ACI, Alloy Casting Institute. Source: Ref 43 Aluminum Aluminum alloy 1100 is more readily attacked...
Series: ASM Handbook
Volume: 22A
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.hb.v22a.a0005442
EISBN: 978-1-62708-196-2
... Corrosion-resistant steel castings CA-15 7.612 0.2750 CA-40 7.612 0.2750 CB-30 7.53 0.272 CC-50 7.53 0.272 CE-30 7.67 0.277 CF-8 7.75 0.280 CF-20 7.75 0.280 CF-8M, CF-12M 7.75 0.280 CF-8C 7.75 0.280 CF-16F 7.75 0.280 CH-20 7.72 0.279 CK-20 7.75...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004219
EISBN: 978-1-62708-184-9
...] CF-8M) stainless steel casting pump case is illustrated in Fig. 4 . This pump case, which was exposed to low pH and high Cl − concentration, failed after approximately 3 years of service. Methods of preventing pitting failures in pump systems would be to prevent any liquid ingress into the contact...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0006543
EISBN: 978-1-62708-183-2
... CA-40 J91153 7.612 0.2750 CB-30 J91803 7.53 0.272 CC-50 J92615 7.53 0.272 CE-30 J93423 7.67 0.277 CF-8, CF-8M J92600 7.75 0.280 CF-20 J92602 7.75 0.280 CF-8C J92710 7.75 0.280 CF-16F J92701 7.75 0.280 CH-20 J93402 7.72 0.279 CK-20 J94202 7.75...
Book Chapter

Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005256
EISBN: 978-1-62708-187-0
.... The technique minimizes dust emissions from molding and finishing, as compared to sand molding. Limitations are: It is not as suitable for thin sections as the lost wax process. It is more expensive than the lost foam process. Fig. 1 Two applications of Replicast steel parts. (a) CF-8M...