1-20 of 311 Search Results for

Bushings

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 1989
Fig. 18 Two setups employing fixtures and bushings for the accurate guiding of reamers More
Image
Published: 01 January 2006
Fig. 8 (a) Demountable and (b) press-fit guide post and bushings More
Image
Published: 01 August 2018
Fig. 54 Eddy-current inspection of cracks located under installed bushings. (a) Schematic of typical assembly employing interference-fit bushings in a clevis/lug attachment assembly. (b) Reference standard incorporating an electrical discharge machined corner notch. (c) Probe coil positioned More
Image
Published: 01 January 1989
Fig. 4 Bushing transducer that mounts on circumference of a machine spindle shaft More
Image
Published: 01 December 2008
Fig. 17 Propeller bushing that was cast in a shell mold without a separate core More
Image
Published: 01 December 2008
Fig. 5 Sprue and sprue bushing area of a low-pressure casting mold. Castings must not solidify below the choke point, to avoid a die-locked condition. More
Image
Published: 01 January 2006
Fig. 5 Guide post/guide bushing deflection More
Image
Published: 01 January 2006
Fig. 9 Hardened steel bushing characteristics (stroke length, 25 mm, or 1 in.) More
Image
Published: 30 November 2018
Fig. 9 Internally threaded rivet bushing (stake nut) joined to mating stamped sheet metal part More
Image
Published: 01 January 2002
Fig. 8 Improper support by a shrink-fitted bushing and a tension overload combined to crack this coining die of type O1 tool steel. More
Image
Published: 01 January 2006
Fig. 6 A noncompatible metal bushing in contact with a stainless steel bolt and other adjacent metal surfaces if left uncorrected may corrode away and weaken the connection. Courtesy of the NRPA NPSI More
Image
Published: 01 January 2005
Fig. 27 Examples of good practice for bushing installations More
Image
Published: 30 August 2021
Fig. 16 Failure of connecting rod due to failure of big-end bushing bearing More
Image
Published: 30 August 2021
Fig. 17 (a) Outside and (b) inside surfaces of failed bushing bearing More
Image
Published: 15 May 2022
Fig. 5 Plastic bushing More
Image
Published: 15 June 2019
Fig. 7 Major types of aluminum bearings. (a) Fixed bearing, consisting of two half-shells. (b) Solid aluminum bushings and thrust washer. (c) Full-floating aluminum bearing used in diesel engine. (d) Full-floating bushing used in compressor. The split in the bushing allows for heat expansion More
Book Chapter

Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005114
EISBN: 978-1-62708-186-3
... Abstract This article briefly describes the nomenclature, alignment and geometrical considerations, and functional and application requirements of a die set. The die set consists of the shank, guide posts, guide bushings, the punch, and die holders. The article illustrates plate flatness...
Image
Published: 01 January 1989
Fig. 4 Incorrect and preferred methods of chip clearance when machining with (a) a drill bushing and (b) a right-angle workpiece. (a) Drill bushing setup at left permits tool drift due to excessive clearance between bushing and workpiece; at center, bushing retains chips because work abuts More
Image
Published: 01 January 1989
Fig. 3 Methods of piloting or supporting boring tools to maintain alignment. (a) Pack head type of pilot. (b) Wear-pad support of trepanning head used for boring large diameter holes from solid stock. (c) Piloted head capable of using several cutting edges. (d) Bushing mounted on auxiliary More
Image
Published: 01 January 2006
Fig. 12 Forms of corrosion in aircraft. (a) Exfoliation corrosion. (b) Microbiologically induced corrosion on fuel tank access door. (c) Bushing assembly. (d) Galvanic corrosion under aluminum-nickel bronze bushing, seen with bushing removed. See the article “Corrosion in Commercial Aviation More