1-20 of 187 Search Results for

Bearing races

Sort by
Image
Published: 01 January 1989
Fig. 31 Setups for microhoning (a) ball bearing races and (b) roller bearing races More
Image
Published: 09 June 2014
Fig. 10 Induction-hardening system for large bearing races. Source: Ref 1 More
Image
Published: 30 September 2015
Fig. 35 Weibull plots of L 10 life of PF bearing races compared with L 10 of wrought and machined races. (a) Cups. (b) Cones. Source: Ref 113 More
Image
Published: 01 January 2005
Fig. 11 Tooling setup for producing bearing races from 3 m (10 ft) lengths of 64 mm (2 1 2 in.) diam bar by upsetting, piercing, and cutoff in two passes. Dimensions given in inches More
Image
Published: 01 January 2005
Fig. 36 Weibull plots of L10 life of P/F bearing races compared with L10 of wrought and machined races. (a) Cups. (b) Cones. Source: Ref 87 More
Image
Published: 01 January 1989
Fig. 17 Setup for lapping inner or outer bearing races More
Image
Published: 01 December 1998
Fig. 5 Flux leakage inspection of a bearing race. (a) Magnetization of inner race. (b) Perturbation in the magnetic flux at the surface of the inner race. (c) Probe scanning the surface More
Image
Published: 30 September 2015
Fig. 34 Raw material utilization in the production of a tapered roller bearing race. (a) Produced from hot rolled tube stock. (b) Powder forged from preform. Source: Ref 112 More
Image
Published: 01 January 2005
Fig. 35 Raw material utilization in the production of a tapered roller bearing race. (a) Produced from hot rolled tube stock. (b) Powder forged from preform. Source: Ref 86 More
Image
Published: 01 January 1989
Fig. 3 Typical bearing race before TEM (left) and after TEM (right) More
Image
Published: 31 August 2017
Fig. 39 High-chromium (ASTM II-D) coal-crushing replacement rollers. The inside bearing races have been machined and are ready for field installation. More
Image
Published: 30 September 2014
Fig. 26 Characteristic roundness plots after heat treatment of thin-walled bearing races by use of linear loading tools. Courtesy of H. Surm. Source: Ref 33 More
Image
Published: 01 January 1987
was 35 HRC. The origin is at arrow A (lower left), at an inclusion. The fatigue crack penetrated as far as the locations indicated by arrows B before final fast fracture occurred. Alignment of the bearing-race parting line (arrows C) was not as specified. Arrow D indicates the region of final fast More
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002373
EISBN: 978-1-62708-193-1
... a race in a ball bearing. The contact geometry and the motion of the rolling elements produces an alternating subsurface shear stress. Subsurface plastic strain builds up with increasing cycles until a crack is generated. The crack then propagates until a pit is formed. Once surface pitting has initiated...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002169
EISBN: 978-1-62708-188-7
... illustrates the capabilities of TEM on a bearing race. This method is equally effective on large and small parts. Figure 4 shows a cast iron housing before and after TEM. Fig. 3 Typical bearing race before TEM (left) and after TEM (right) Fig. 4 Cast iron housing before TEM (left) and after...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003233
EISBN: 978-1-62708-199-3
... associated with broken strands is measured using a Hall effect probe or an auxilliary sensor coil. Another area that uses the flux leakage method is inspection of rolling-element antifriction bearings. A schematic illustration of the method as applied to an inner bearing race is shown in Fig. 5...
Image
Published: 01 January 2005
Fig. 30 Ball bearing outer race that was cold forged from sintered powder preform of 4620 lowalloy steel More
Image
Published: 01 January 2005
Fig. 32 Preform alternatives for forging the ball bearing outer race shown in Fig. 30 . (a) Back extrusion. (b) Compression and radial inward flow More
Image
Published: 01 January 2005
Fig. 4 Examples of contour ring shapes. (a) Roller bearing inner race. (b) C-shaped ring More
Image
Published: 01 January 1996
Fig. 2 Anatomy of a race spall in a ball bearing. (a) Typical delta shape with the apex at the origin. (b) Profiles of the spall. Source: Ref 2 More