1-20 of 293 Search Results for

Bearing caps

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 30 November 2018
Fig. 1 Examples of some small aluminum camshaft bearing caps produced by powder metallurgy More
Image
Published: 01 January 1989
Fig. 34 Die cast engine block that was honed with gray iron bearing caps in place, and honing tool that was used (bottom). Dimensions in figure given in inches Speed, at 900 rev/min, m/min (sfm) 190 (620) Spindle reciprocation rate, strokes/min 60 Hone speed, m/min (sfm) 21 (70 More
Image
Published: 30 September 2015
Fig. 1 Examples of some small aluminum camshaft bearing caps produced by powder metallurgy More
Image
Published: 30 November 2018
Fig. 2 Powder metallurgy aluminum camshaft bearing cap. 2006 Grand Prize award winner in the automotive category. Courtesy of Metal Powder Products, General Motors, and Metal Powder Industries Federation. Source: Ref 5 More
Image
Published: 30 September 2015
Fig. 24 Powder metallurgy aluminum camshaft-bearing cap. Metal Powder Products Co., courtesy of MPIF More
Image
Published: 30 September 2015
Fig. 2 PM aluminum camshaft bearing cap. 2006 Grand Prize award winner in the automotive category. Courtesy of Metal Powder Products, GM, and MPIF. Source: Ref 5 More
Image
Published: 01 January 2002
Fig. 44 Micrograph from the cope side of the main-bearing journal. Ferrite caps, which partially cover the graphite nodules and cause the broken-open surface condition, are shown. The burrs rise above the surface from 4 to 13 μm. Etched with nital. 220× More
Image
Published: 30 August 2021
Fig. 26 Micrograph from the cope side of the main-bearing journal. Ferrite caps, which partially cover the graphite nodules and cause the broken-open surface condition, are shown. The burrs rise above the surface from 4 to 13 μm. Etched with nital. Original magnification: 220× More
Series: ASM Handbook
Volume: 7
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v07.a0006132
EISBN: 978-1-62708-175-7
... Abstract The powder metallurgy (PM) process is a relatively efficient and economic process that can be used to produce high quantities of aluminum components with a reasonable degree of precision and finds application in camshaft bearing cap (cam cap) production. The article discusses...
Series: ASM Handbook Archive
Volume: 12
Publisher: ASM International
Published: 01 January 1987
DOI: 10.31399/asm.hb.v12.a0000608
EISBN: 978-1-62708-181-8
..., sulfide stress-corrosion failure, stress-corrosion cracking, and hitch post shaft failure of these steels. The components considered in the article include tail-rotor drive-pinion shafts, pinion gears, outboard-motor crankshafts, bull gears, diesel engine bearing cap bolts, splined shafts, aircraft...
Image
Published: 01 January 2002
Fig. 14 Bearing halves (a) that failed by fatigue resulting from localized overloading after bearing cap shifted position. (b) Note the damaged areas (arrows A and B) on diametrically opposite sides of the bearing halves where they contacted the shaft after the cap shifted. More
Image
Published: 30 August 2021
Fig. 10 Bearing halves failed by adhesive wear resulting from localized overloading after bearing cap shifted position. More
Image
Published: 30 August 2021
Fig. 30 Fractured axle journal within bearing. The end cap was removed from the failed side. A noticeable amount of red rust was present on the interior of the end cap, as seen in Fig. 32 . The journal stub was pressed out of the bearing. Present on the end of the journal was the axle More
Image
Published: 30 August 2021
Fig. 32 Inside of subject bearing end cap More
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001812
EISBN: 978-1-62708-180-1
... failure. 4× Investigation Visual examination of the assembly showed that three of four bearing caps, two cap screws, and one universal-joint spider had fractured. Examination of the three fractured bearing caps and the spider showed no evidence of fatigue, but showed that fracture occurred...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006805
EISBN: 978-1-62708-329-4
...× Investigation Visual examination of the assembly showed that three of four bearing caps, two cap screws, and one universal-joint spider had fractured. Examination of the three fractured bearing caps and the spider showed no evidence of fatigue but showed that fracture occurred in a brittle manner...
Image
Published: 01 January 1987
occurred in the shaft at the moment of initial fracture or whether the segment broke away later due to impact within the cylinder before the engine was shut off. The fracture surface visible here bears no features that in any way suggest a fatigue fracture. The 4340 steel bolts (left of cap at far right More
Image
Published: 30 August 2021
Fig. 12 One-half of wheelset showing journal fillet (blue arrow), backing ring blend radius (white arrow), cartridge bearing, and end cap (at left) More
Image
Published: 01 January 2005
Fig. 3 Examples of forgings that illustrate typical web designs. (a) Large steel crown fitting with flat, confined, and unconfined webs. (b) Small A-286 cam actuator link with thin, flat, confined web. (c) Small A-286 bearing housing with unconfined web at corners. (d) Large aluminum alloy More
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006497
EISBN: 978-1-62708-207-5
... injection molding, powder forging, and additive manufacturing. Conventional PM is a highly efficient manufacturing technology for high-volume production of aluminum components. The first high-volume PM production part, called a camshaft bearing cap, or cam cap, was shipped to General Motors Corporation (now...