1-20 of 75 Search Results for

2.25Cr-1Mo

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 1986
Fig. 18 AP mass spectrum of a carbide particle in a tempered 2.25Cr-1Mo steel. Source: Ref 6 More
Image
Published: 01 January 2002
Fig. 16 2.25Cr-1Mo steel superheater tube that failed by creep. (a) As-received failure. (b) Microstructure of the whole tube section is spheroidized carbides in ferrite. Etched with nital. 500× More
Image
Published: 01 January 2002
Fig. 28 2.25Cr-1Mo steel superheater tube that ruptured because of thinning by coal-ash corrosion. More
Image
Published: 01 January 2002
Fig. 32 Metallographic cross section through failure in 2.25Cr-1Mo weld main steam line of power plant. Secondary cracking in base metal indicates that failure is not uniquely the result of weld-metal properties. More
Image
Published: 01 January 2000
Fig. 3 Creep curve of 2.25Cr-1Mo steel with nonclassical early stage. Normalized and tempered to 607 MPa (88 ksi) tensile strength at room temperature. Tested at 482 °C (900 °F) at 275.8 MPa (40 ksi) More
Image
Published: 01 December 2004
Fig. 7 2.25Cr-1Mo steel plate, single-pass electron beam weld. Heat input: 0.5 MJ/m. Macrostructure shows high depth-to-width ratio of the fusion zone, which is typical of high-energy density welding processes. Etchant: 85 mL H 2 O + 15 mL HNO 3 + 5 mL methanol. Magnification: 2.8× More
Image
Published: 01 January 1996
Fig. 20 Corrosion fatigue in 2.25Cr-1Mo pressure-vessel steel in hydrogen due to hydrogen embrittlement at high Δ K and to reduced oxide-induced closure at low Δ K. Stress ration = 0.05. Source: S. Suresh and R.O. Ritchie, Metals Science , Vol. 16, 1982, p 529–538 More
Image
Published: 30 August 2021
Fig. 55 Metallographic cross section through failure in 2.25Cr-1Mo weld main steam line of power plant. Secondary cracking in base metal indicates that failure is not uniquely the result of weld metal properties. More
Image
Published: 01 January 1996
Fig. 16 Fatigue crack growth rate as a function of Δ K for mod. 9Cr-1Mo, 9Cr-2Mo, 2Mo, and 2.25Cr-1Mo steels in vacuum at 538 °C. Source: Ref 90 More
Image
Published: 15 January 2021
Fig. 17 Isothermal diagram showing the sequence of carbide formation on tempering of normalized 2.25Cr-1Mo steel. Source: Ref 22 More
Image
Published: 15 January 2021
Fig. 19 Total strain range versus cycles to failure for isothermally annealed 2.25Cr-1Mo steel at 427 and 538 °C (800 and 1000 °F). Source: Ref 34 More
Image
Published: 01 January 2002
Fig. 15 Total strain range versus cycles to failure for isothermally annealed 2.25Cr-1Mo steel at 427 and 538 °C (800 and 1000 °F). Source: Ref 21 More
Image
Published: 30 August 2021
Fig. 24 Microstructure of (a) crack location adjacent to stainless steel side, showing intergranular nature, (b) base metal of stainless steel, and (c) base metal of low-alloy (2.25Cr-1Mo) steel. Source: Ref 6 More
Image
Published: 15 January 2021
Fig. 17 Effect of hold time on the fatigue crack growth rate properties of 2.25Cr-1Mo cast steel. The 2 h hold time tests were performed in steam at 538 °C (1000 °F). Source: Ref 28 More
Image
Published: 01 January 2002
Fig. 13 Effect of hold time on the fatigue crack growth rate properties of 2.25Cr-1Mo cast steel. The 2 h hold time tests were performed in steam at 538 °C (100 °F). Source: Ref 13 More
Image
Published: 01 January 1990
bubbles in 2.25Cr-1Mo steel. Source: Ref 53 More
Image
Published: 01 January 1990
Fig. 27 Variation of tear test toughness with location in a plate. Variations in toughness were measured by drop-weight tear tests across the thickness of a 102 mm (4 in.) thick plate on ASTM A 387 (2.25Cr-1Mo) steel. The curve labeled 1 4 t was obtained from specimens taken More
Series: ASM Handbook
Volume: 1
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v01.a0001035
EISBN: 978-1-62708-161-0
... Maximum-use temperature Oxidation/graphitization criteria, metal surface (a) Strength criteria, metal midsection °C °F °C °F SA-106 carbon steel 400–500 750–930 425 795 Ferritic alloy steels  0.5Cr-0.5Mo 550 1020 510 950  1.2Cr-0.5Mo 565 1050 560 1040  2.25Cr-1Mo...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003546
EISBN: 978-1-62708-180-1
... studies, in which practical systems are analyzed from a fracture mechanics perspective are also presented in Ref 11 . Casings for a ship service turbine generator (SSTG) are cast from 2.25Cr-1Mo steel and are designed to provide service for 30 years. The regions of the casings in the vicinity...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006781
EISBN: 978-1-62708-295-2
... from 2.25Cr-1Mo steel and are designed to provide service for 30 years. The regions of the casings in the vicinity of the steam chest and the steam passageways are subjected to high transient thermal stresses during startup and to moderate steady-state mechanical stresses during sustained operation...