Optical testing of plastics includes the characterization of materials and the analysis of optical components. If a material is tested for transmission, haze, yellowness, and refractive index, the knowledge of its optical properties is nearly complete. For optical components, surface irregularity, birefringence, and internal contamination must also be considered. These characteristics are a function of the material and the fabrication method. Gloss and color also are affected by the base material and measured as optical properties.

This article addresses electrical testing and characterization of plastics and presents a number of techniques for evaluating the electrical properties of insulating materials, with a special focus on plastics, accompanied by a list of the electrical properties of different types of plastics. It provides the reader with sufficient information to select the appropriate electrical test(s) for a specific application. The tests covered in this article are widely used in industry to determine the electrical properties of insulating materials, particularly plastics. The article lists and defines terms used in connection with testing and specification of plastics for electrical applications.

Laser-ultrasonics is a particular implementation of ultrasonic nondestructive inspection in which ultrasound is generated and detected by lasers. This article discusses the various mechanisms that ensure ultrasound generation and explains the possibility to get the equivalent of phase-array by numerical processing of an array of previously acquired laser-ultrasonic signals. The article describes the ultrasound generation by thermoelastic mechanism and ablation or vaporization. It illustrates the principle of optical detection of ultrasound with confocal Fabry-Perot interferometer and photorefractive two-wave mixing interferometer. The article concludes with information on the industrial applications of laser-ultrasonics, including thickness measurement, flaw detection, and material characterization.

The potential for introducing defects during processing becomes greater as the relative density of pressed and sintered powder metallurgy (PM) parts increases and more multilevel parts with complex geometric shapes are produced. This article discusses the potential defects in pressed and sintered PM parts: density variations, compaction and ejection cracks, microlaminations, poor degree of sintering, and voids from prior lubricant agglomerates. It describes the various methods applicable to green compacts: direct-current resistivity testing, radiographic techniques, computed tomography, and gamma-ray density determination. The article also discusses the methods for automated nondestructive testing of pressed and sintered PM parts: acoustic methods-resonance testing, eddy current testing, magnetic bridge comparator testing, ultrasonic techniques, radiographic techniques, gamma-ray density determination, and visual inspection.

This article provides information on the application of nondestructive examination (NDE) technologies to tube and pipe products. These include modeling and simulation methods, eddy-current methods, magnetic methods, acoustic methods, and physical methods. A summary of nondestructive examination methods based on flaw type and product stage is presented in a table. The article also discusses in-service inspection of tubular products and presents an example that illustrates the importance of nondestructive testing (NDT) for welds in austenitic stainless steel tubing.

This article focuses on friction and wear of automotive and aircraft brakes. It provides a comparison of friction and wear behaviors, frictional characteristics, and frictional performance of the friction materials. The article describes the components of brake friction materials and the classifications of brake lining materials. It discusses the effect of formulation compositions and manufacturing processes and the effect of braking operation conditions. The article provides information on aircraft brake linings, which operate under a wide range of kinetic energy conditions. The morphology effect of graphite on automotive brake drum and disk is explained. The article also describes the characteristics of specific wear rates for both normal and local cast iron in automotive brake drums and disk rotors. It provides information on noises, vibrations, and harshness caused by brake pads. The article concludes with information on physical and chemical testing of brakes and toxicity of brake formulation and regulations.

Several qualitative, semiquantitative, and quantitative tests are available to estimate and control metal cleanliness, particularly inclusion concentration of aluminum alloys. This article provides a description of a few of the metal cleanliness assessment techniques, such as chemical analysis, pressure filter tests, electric resistivity tests, reduced-pressure test, and ultrasonic technique. Detection methods based on the certain principles and the types of impurities in chemical analysis are discussed.

Steel storage tanks are the primary means for storing large volumes of liquids and gaseous products. The stored fluid could be water, but it could also be volatile, corrosive, and flammable fluid requiring special precautions for storage as well. Corrosion is generally worst where the tank is in contact with the soil. This article describes the soil characteristics and addresses cathodic protection (CP) criteria for submerged metallic piping systems. It provides information on the data required for designing a CP system, alone or in conjunction with a protective coating system. These data are collected from predesign site assessments, tank electrical characteristics, and soil-resistivity measurements. The article addresses NACE Standard RP0169, which gives requirements and desired characteristics for coating in conjunction with CP. It also explains the methods of protecting aboveground storage tanks and underground storage tanks.

This article explores the use of the electrochemical and nonelectrochemical techniques for measuring the corrosion behavior of buried metals and the types of probes used. The electrical resistance technique is the main nonelectrochemical technique used for measuring corrosion rate. Electrochemical techniques discussed include linear polarization resistance, electrochemical noise, harmonic distortion analysis, electrochemical impedance spectroscopy, and hydrogen permeation. The principles of operation for the corrosion measuring techniques are described along with examples of their use in soils.

Sheet metal forming operations are so diverse in type, extent, and rate that no single test provides an accurate indication of the formability of a material in all situations. This article presents an overview of types of forming, formability problems, and principal methods of measuring deformation. It reviews the effect of materials properties and temperature on formability. The article provides a detailed discussion on the two major categories of formability tests such as the intrinsic test, including uniaxial tension testing, plane-strain tension testing, biaxial stretch testing, and simulative tests such as bending tests, stretching tests, the Ohio State University test, the drawing test, and stretch-drawing tests. It extends the correlation between simulative tests and materials properties using forming limit diagrams and circle grid analysis, and discusses the improvements to the forming limit diagram technology.

Rough grinding and polishing of specimens are required to prepare fiber-reinforced composite samples for optical analysis. This article discusses the consumables, process variables, and the equipment that influence the sample preparation procedure. It describes the hand and automated grinding methods. The article summarizes the rough and final polishing steps for both hand and automated techniques. Common artifacts that may be created during grinding and polishing steps of composite samples are reviewed. These include scratches, fiber pull-out, matrix smears, streaks, erosion of different phases, and fiber and sample edge rounding and relief.

This article focuses on the sample preparation methods for titanium honeycomb composites, boron fiber composites, and titanium/polymeric composite hybrids. These include mounting, sectioning, grinding, and polishing. The article also provides information on the sample preparation of unstaged and staged prepreg materials for optical analysis.

This article is a compilation of color etchants that have been developed for a limited number of metals and alloys. It describes the optical methods for producing color, such as polarized light and differential interference contrast, with illustrations. The article discusses film formation and interference techniques such as anodizing, chemical etching, and tint etching. It provides a description of reagents that deposit sulfide films and molybdate films. The article concludes with a discussion on the thermal and vapor deposition methods to produce color.

This article addresses electrochemical methods for instantaneous rate determination and threshold determination as well as nonelectrochemical methods that can determine incremental or cumulative rates of corrosion. Electrochemical methods for the study of galvanic corrosion rates and localized corrosion and evaluation of corrosion rates under paints are also discussed. The article describes nonelectrochemical methods that can determine incremental or cumulative rates of corrosion. Methods presented include polarization methods, polarization resistance methods, electrochemical impedance methods, frequency modulation methods, electrochemical noise resistance, potential probe methods, cyclic potentiodynamic polarization methods, potentiostatic and galvanostatic methods, electrochemical noise (EN) methods, scratch-repassivation method, and electrochemical impedance spectroscopy (EIS) techniques. Gravimetric determination of mass loss, electrical-resistance methods, magnetic methods, quartz crystal microbalance method, solution analysis methods, and metrological methods are nonelectrochemical methods. The article presents an electrochemical test that examines the susceptibility of stainless steel alloys to intergranular corrosion.

This article introduces the principal methodologies and some technologies that are being applied for nondestructive evaluation of composite materials. These include ultrasonic testing (UT), air-coupled UT, laser UT, ultrasonic spectroscopy, leaky lamb wave method, acousto-ultrasonics, radiography, X-ray computed tomography, thermography, low-frequency vibration methods, acoustic emission, eddy current testing, optical holography, and shearography. The article presents some examples are for fiber-reinforced polymer-matrix composites. Many of the techniques have general applicability to other types of composites such as metal-matrix composites and ceramic-matrix composites.

This article describes the most significant tests to characterize the properties of constituent materials. It discusses the chemical, physical, and mechanical tests for determining the properties of reinforcement fibers and fabrics. The article provides information on some of the basic materials used for thermoset and thermoplastic resin matrices. It reviews the identification of the individual characteristics of thermoset and thermoplastic resin along with the test methods normally used for their determination. The article contains a table that lists properties and tests for uncured and cured thermoset-matrix resins and prepregs.

The study of the physical properties of ductile solids subjected to shock wave loading is undertaken to understand how the thermodynamic conditions and strain rate affect material response. This article presents a description of a range of possible experimental techniques to quantify the structure/property effects of planar shock waves on ductile materials (metals and alloys) due to the wave propagation through the material. The techniques include explosive-driven shock-loading methods, shock-loading methods using exploding foil and laser-driven impactors, gas/powder launcher-driven shock loading methods, and radiation-driven shock-loading methods. Design parameters for shock recovery fixtures, spallation fixtures, and the flyer-plate experiment, are also discussed.

Impact tests are used to study dynamic deformation and failure modes of materials. This article discusses low-velocity impact experiments in single-stage gas guns. It describes surface velocity measurements with laser interferometric techniques. The article details plate impact soft-recovery experiments, pressure-shear friction experiments, and low-velocity penetration experiments. It reviews two types of plate impact soft-recovery experiments: normal plate impact and pressure-shear plate impact experiments. The article provides information on low-velocity penetration experiments, which include the setup for direct penetration experiment (rod-on-plate) and the reverse penetration experiment (plate-on-rod). It also considers high-temperature plate impact testing and impact techniques with in-material stress and velocity measurements.

Testing and characterization of fatigue crack growth are used extensively to predict the rate at which subcritical cracks grow due to fatigue loading. ASTM standard E 647 is the accepted guideline for fatigue crack growth testing (FCGR) and is applicable to a wide variety of materials and growth rates. The two most widely used types of specimens are the middle-crack tension and compact-type specimens. This article describes the factors affecting the selection of appropriate geometries of these specimens: consideration of material availability and raw form, desired loading condition, and equipment limitations. Various crack measurement techniques, including optical, ultrasonic, acoustic emission, electrical, and compliance methods, are also reviewed. The article discusses the two major aspects of FCGR test analysis: to ensure suitability of the test data and to calculate growth rates from the data.

This article describes the test techniques that are available for monitoring crack initiation and crack growth and for obtaining information on fatigue damage in test specimens. These techniques include optical methods, the compliance method, electric potential measurement, and gel electrode imaging methods. The article discusses the magnetic techniques that are primarily used as inspection techniques for detecting fatigue cracks in structural components. It details the principles and operation procedures of the liquid penetrant methods, positron annihilation techniques, acoustic emission techniques, ultrasonic methods, eddy current techniques, infrared techniques, exoelectron methods, and gamma radiography. The article explains the microscopy methods used to determine fatigue crack initiation and propagation. These include electron microscopy, scanning tunneling microscopy, atomic force microscopy, and scanning acoustic microscopy. The article also reviews the X-ray diffraction technique used for determining the compositional changes, strain changes, and residual stress evaluation during the fatigue process.