Powder bed fusion (PBF) of polymers is a collection of additive manufacturing processes that melt and fuse polymer in a powder bed. This article provides a complete suite of materials and processes involved in PBF of polymers. The discussion includes details of thermal and manufacturing issues, and safety, postprocessing, and finishing considerations, as well as of principal defects in PBF polymer parts and the mechanical properties of the parts produced by PBF. The article provides case studies on the applications of polymer PBF.

This article provides a general overview of additively manufactured steels and focuses on specific challenges and opportunities associated with additive manufacturing (AM) stainless steels. It briefly reviews the classification of the different types of steels, the most common AM processes used for steel, and available powder feedstock characteristics. The article emphasizes the characteristics of the as-built microstructure, including porosity, inclusions, and residual stresses. It also reviews the material properties of AM steel parts, including hardness, tensile strength, and fatigue strength, as well as environmental properties with respect to corrosion resistance, highlighting the importance of postbuild thermal processing.

Wrought heat treatable 7xxx alloys are more responsive to precipitation hardening than the 2xxx series alloys and can achieve higher strength levels, approaching tensile strengths of 690 MPa (100 ksi). This article provides an overview of key metallurgy, properties, and applications of the 7xxx aluminum alloy. It also illustrates the natural aging characteristics of 7050 aluminum sheet alloys at room temperature and relationships among commonly used alloys in the 7xxx series.

The 206.0, A206.0, and B206.0 alloys (aluminum alloys 2xxx) are structural castings in the heat-treated temper for automotive and aerospace applications where high tensile and yield strengths with moderate elongations are needed. This datasheet provides information on key alloy metallurgy and fabrication characteristics of these 2xxx series alloys, as well as the effects of processing on their typical physical and mechanical properties.

This article describes different methods by which the composition of cast iron can be analyzed. It provides particular emphasis on the methods for evaluating the graphitization potential of a melt with prescribed limits on carbon, silicon, and alloying elements. The article discusses the effect of cooling rate on the graphitization of a given composition by chill and wedge tests. Thermal analysis of cooling curves gives excellent information about the solidification and subsequent cooling of cast iron alloys. The article presents some applications of the cooling curve analysis and explains the evaluation of carbon-silicon contents, graphite shape, graphite nucleation, and contraction-expansion balance. It illustrates the use of an immersion steel sampling device for compacted graphite iron production and provides information on the ferrite-pearlite ratio in ductile iron.

Gray irons are a group of cast irons that form flake graphite during solidification, in contrast to the spheroidal graphite morphology of ductile irons. This article describes surface hardening of gray irons by flame and induction heating. It provides information on the classification of the gray irons in ASTM specification. The article presents examples that illustrate the use of stress relieving to eliminate distortion and cracking. It describes the three annealing treatments of gray iron: ferritizing annealing, medium (or full) annealing, and graphitizing annealing. The article discusses the parameters of the tensile strength and hardness of a normalized gray iron casting. These include combined carbon content, pearlite spacing, and graphite morphology. The article concludes with a discussion on the induction hardening of gray iron castings.

Compacted graphite iron (CGI) invariably includes some nodular (spheroidal) graphite particles, giving rise to the definition of the microstructure in terms of percent nodularity. This article discusses the graphite morphology and mechanical and physical properties of CGI. The mechanical and physical properties of CGI with ferritic and pearlitic matrix structures are summarized in a table. The article describes the standards for CGI, with the definition of the grades based on the minimum tensile strength. It also provides information on the applications of compacted graphite iron castings.

Gray irons are commonly classified by their minimum tensile strength. This article describes properties used in the selection of gray irons and the factors that affect properties, particularly the effect of solidification. It discusses the three steps that its processing undergoes in the foundry: liquid metal preparation, solidification, and solid-state transformation. The article discusses the tensile properties of gray cast iron: tensile strength, yield strength, ductility, and modulus of elasticity. It describes hardness tests that are performed for determining the approximate strength characteristics and machinability of a gray iron casting. The article also presents typical mechanical properties of heat-resistant gray irons in a table. It concludes with information on the automotive application of alloy cast irons.

Ductile iron, also known as nodular iron or spheroidal graphite iron, is second to gray iron in the amount of casting produced. This article discusses the common grades of ductile iron that differ primarily by the matrix structure that contains the spherical graphite. The grades of ductile iron designated by their tensile properties in the specification ASTM A536 are presented in a table. The article various reviews factors, such as microstructure, composition, and section effect, affecting the mechanical properties of ductile iron. It discusses the hardness properties, tensile properties, shear and torsional properties, damping capacity, compressive properties, fatigue properties, and fracture toughness of ductile iron. The article concludes with information on the applications of austempered ductile iron.

This article provides useful information on the selection of steels for heat treatment in order to achieve the required hardness. It discusses the effects of alloying elements on hardenability using the Grossmann's concept, and presents a discussion on the effects of alloying elements in hot-worked and cold-drawn steels. The article focuses on the selection of carbon and alloy steels based on the function of the alloying elements, and discusses the specific effects of alloying elements in steel in a tabulated form. The depth and degree of hardening (percentage of martensite) are dictated by the engineering stress analysis. Mechanical properties of quenched and tempered steels develop similar tensile properties for all practical purposes for all compositions with the same hardness. The article also provides information on the selection of steels to meet the required hardness, and elucidates the concept of hardenability for wear resistance with the help of graphs.

Tempering of steel is a process in which hardened or normalized steel is heated to a temperature below the lower critical temperature and cooled at a suitable rate, primarily to increase ductility, toughness, and grain size of the matrix. This article provides an overview of the variables that affect the microstructure and mechanical properties of tempered steel, namely, the tempering temperature, tempering time, carbon content, alloy content, and residual elements. Tempering after hardening is performed to relieve quenching stresses and ensure dimensional stability of steel. The article discusses the embrittlement problems associated with tempering. Four types of equipment are used for tempering, namely, convection furnaces, salt bath furnaces, oil bath equipment and molten metal baths. Special procedures for tempering are briefly reviewed.

Shell molding is used for making production quantities of castings that range in weight from a few ounces to approximately 180 kg (400 lb), in both ferrous and nonferrous metals. This article lists the limitations or disadvantages of shell mold casting. It describes the two methods for preparation of resin-sand mixture for shell molding, namely, mixing resin and sand according to conventional dry mixing techniques, and coating the sand with resin. Shaping of shell molds and cores from resin sand mixtures is accomplished in machines. The article discusses the major steps in producing a mold or core and describes the problems most frequently encountered in shell-mold casting. The problems include mold cracking, soft molds, low hot tensile strength of molds, peelback, and mold shift. The article concludes with information on examples that provide some relative cost comparisons between shell molding and green sand molding.

Workability in forging depends on a variety of material, process-variable, and die-design features. A number of test techniques have been developed for gaging forgeability depending on alloy type, microstructure, die geometry, and process variables. This article summarizes some common workability tests and illustrates their application in practical forging situations. Workability tests for open-die forging of cast structures, hot and cold open-die forging of recrystallized structures, fracture-controlled defect formation, establishing effects of process variables and secondary tensile stresses on forgeability, and flow-localization-controlled failure are some common tests. The workability test used for closed-die forging is also summarized.

A cylindrical specimen compressed with friction at the die surfaces does not remain cylindrical in shape but becomes bulged or barreled. Tensile stresses associated with the bulging surface make the upset test a candidate for workability testing. This article discusses test-specimen geometry and friction conditions; strain measurements; crack detection; and material inhomogeneities, which are to be considered for performing cold upset testing. It describes test characteristics in terms of deformation, free-surface strains, and stress states for performing cylindrical compression tests. The article illustrates the fracture loci in cylindrical, tapered, and flanged upset-test specimens of aluminum alloy and type 1045 cold-finished steel.

This article describes the roll forming of components of nickel, titanium, and aluminum alloys. The metallurgical characteristics of the roll formed components, such as macrostructures, microstructures, tensile strength, and stress rupture performance, are discussed. The article compares the resulting properties of roll formed and conventionally forged components.

Hydrogen damage is a form of environmentally assisted failure that results from the combined action of hydrogen and residual or applied tensile stress. This article classifies the various forms of hydrogen damage and summarizes the theories that seek to explain these types of degradation. It reviews hydrogen degradation in specific ferrous and nonferrous alloys, namely, iron-base alloys, nickel alloys, aluminum alloys, copper alloys, titanium alloys, zirconium alloys, and vanadium, niobium, tantalum, and their alloys. An outline of hydrogen damage in intermetallic compounds is also provided.

The chemical composition of Kevlar aramid fiber is poly para-phenyleneterephthalamide. Para-aramid fibers belong to a class of materials known as liquid crystalline polymers. This article discusses the manufacture of aramid fibers and the major fiber forms, such as continuous filament yarns, rovings, woven fabrics, discontinuous staple and spun yarns, fabrics, and pulp. Key representative properties of para-aramid fibers are listed in a table. The article reviews the properties of aramid fibers, including tensile modulus, tensile strength, creep and fatigue, compressive properties, toughness, thermal properties, as well as electrical and optical properties. It concludes with a discussion on the environmental behavior of para-aramid fibers.

THE TENSION TEST is one of the most commonly used tests for evaluating materials. The material characteristics obtained from tension tests are used for quality control in production, for ranking performance of structural materials, for evaluation of alloys, and for dealing with the static-strength requirements of design. This article describes the stress-strain behavior during a tension test and provides the definition of terms such as stress, force, strain, and elongation. It explains the tensile properties obtained from the test results: the tensile strength and yield strength, which includes offset yield strength, extension-under-load yield strength, and upper yield strength. The article concludes with a description of the general procedures for conducting the tension test based on ASTM standards and the variability of tensile properties.

This article reviews the factors that have a significant effect on the selection and interpretation of results of different hardness tests, namely, Brinell, Rockwell, Vickers, and Knoop tests. The factors concerned include hardness level (and scale limitations), specimen thickness, size and shape of the workpiece, specimen surface flatness and surface condition, and indent location. The article focuses on the selection for specific types of materials, such as steels, cast irons, nonferrous alloys, and plastics, and industrial applications, of hardness tests.

This article discusses the standard test methods that can be applied to many types of welds: tension, bending, impact, and toughness testing. It provides information on four qualification stages, namely, the weld material qualification, base material qualification, the weld procedure qualification, and the weld service assessment. The article describes two general types of measurements for residual stress in welds: locally destructive techniques and nondestructive techniques. Locally destructive techniques include hole drilling, chip machining, and block sectioning. Nondestructive techniques include X-ray diffraction, neutron diffraction, Barkhausen noise analysis, and ultrasonic propagation analysis. The article concludes with an overview of weldability testing.