The extrusion and sheet alloy 6056 was developed to provide weldable thin extrusions with an excellent balance between high strength and corrosion resistance. This datasheet provides information on composition limits, processing effects on mechanical properties, and applications of this 6xxx series alloy. It provides a material performance comparison of aluminum alloys 6056-T6511 with 2024-T3511 and 6056-T8511 with 2024-T3511.

Alloy 2519 is an Al-Cu alloy that was developed as a higher strength weldable alloy for armor plate. This datasheet provides information on key alloy metallurgy of alloy 2519 and processing effects on mechanical properties of 2519-T87 plate.

Alloy 5083 is a moderate-strength weldable alloy differentiated from alloy 5086 by the higher nominal magnesium and manganese contents. This datasheet provides information on composition limits, product specifications, fabrication characteristics, processing effects on physical and mechanical properties, and applications of this 5xxx series alloy.

Alloy 6156 is an Al-Si-Mg-Cu-Mn weldable alloy, developed for the lower portion of the fuselage, which required a T6 temper strength level and high damage tolerance properties. This datasheet provides information on key alloy metallurgy of this 6xxx series alloy. Fatigue crack growth and material toughness for various thicknesses of alloy 6156 clad T62 are illustrated.

The moderate-strength weldable alloy 5086 provides higher strength than alloy 5052 while maintaining good corrosion resistance in a marine environment. This datasheet provides information on key alloy metallurgy, processing effects on physical and tensile properties, product specifications, and fabrication characteristics of this 5xxx series alloy.

The resistance welding processes commonly employed for joining aluminum are resistance spot welding, resistance seam welding, resistance roll welding, upset and flash welding for butt joining welding, and high-frequency resistance welding. This article discusses the general factors affecting resistance welding: electrical and thermal conductivities, rising temperature, plastic range, shrinkage, and surface oxide. It reviews the weldability of base materials such as Alclad alloys and aluminum metal-matrix composites. The article describes the joint design and welding procedures for resistance spot welding, as well as the joint type, equipment, and welding procedures for seam and roll spot welding. It concludes with information on flash welding, high-frequency welding, and cross-wire welding.

Weldability is a function of three major factors: base material quality, welding process, and design. This article focuses on base-metal weldability of aluminum alloys in terms of mechanical property degradation in both the weld region and heat-affected zone, weld porosity, and susceptibility to solidification cracking and liquation cracking. It provides an overview on welding processes, including gas metal arc welding, gas tungsten arc welding, resistance spot and seam welding, laser beam welding, and various solid-state welding processes. A review on joint design is also included, mainly in the general factors associated with service weldability (fitness). The article also provides a discussion on the selection and weldability of non-heat-treatable aluminum alloys, heat treatable aluminum alloys, aluminum-lithium alloys, and aluminum metal-matrix composites.

This article characterizes the physical differences between powder metallurgy (PM) and wrought or cast materials, as they apply to joining. It discusses acceptable joining procedures and techniques, including welding and brazing and solid-state methods. Information on the weldability of various PM materials is presented. The article also describes the effects of porosity on several important properties that affect the welding characteristics.

Powder metallurgy (PM) stainless steels, as with conventional PM steels, are often used in the as-sintered condition. In addition to cost considerations, minimization of postsinter handling and secondary operations is also preferred because it reduces the potential for contamination of the parts with particulates and residues, which can result in the appearance of surface rust. This article provides information on various secondary operations, including tumbling, re-pressing, resin impregnation, annealing or heat treating, brazing, machining, and welding. It describes those aspects relating to welding of PM stainless steels, specifically, the effects of density, residual porosity, and sintered chemistry on weldability. Further, the article investigates the influence the sintering atmosphere has on machinability, as well as differences created by the presence of residual porosity.

This article provides an overview of integrated weld modeling and discusses the fundamentals of the underlying physics and methodologies involved in process modeling. It presents approaches for microstructure modeling that help to predict phase fractions as well as grain size in the heat-affected zone and weld metal region as a function of alloy composition and thermal cycles. The article discusses the uses of computational thermodynamic and kinetic tools. It describes the concept of performance modeling, whose goal relates to the prediction of weldability, geometrical distortion, and/or locked-in residual stress as a function of material, restraint, process, and process parameters as well as service temperature. Finally, the article presents a case study, evaluating the use of X-65 steels using the E-WeldPredictor tool.

Weldability refers to the ease of welding a material under the imposed fabrication conditions to perform satisfactorily during service. This article is a comprehensive collection of tables that summarize the general weldability of cast irons, steels, nonferrous metals, and their alloys by common fusion welding processes.

This article provides an overview of integrated weld modeling and presents strategic goals for the welding industry. It discusses the fundamentals of the underlying physics and the methodologies to solve the same. The article presents the pioneering work done to predict the heat-affected zone and weld metal microstructure in the early 1980s and 1990s. Applications of computational thermodynamics and kinetics tools to weld metal microstructure prediction for liquid-gas reactions and liquid-slag reactions that happen as a function of high-to-low temperature during fusion welding are discussed. The article also includes a brief discussion on weldability prediction, residual stress prediction, and distortion prediction. It concludes with information on the use of optimization methodologies.

This article briefly reviews the general causes of weldment failures, which may arise from rejection after inspection or failure to pass mechanical testing as well as loss of function in service. It focuses on the general discontinuities observed in welds, and shows how some imperfections may be tolerable and how the other may be root-cause defects in service failures. The article explains the effects of joint design on weldment integrity. It outlines the origins of failure associated with the inherent discontinuity of welds and the imperfections that might be introduced from arc welding processes. The article also describes failure origins in other welding processes, such as electroslag welds, electrogas welds, flash welds, upset butt welds, flash welds, electron and laser beam weld, and high-frequency induction welds.

The selection of the best material for a particular design is intimately associated with the decisions of how to process the material or manufacture a part. This article describes the basic characteristics of manufacturing processes such as material factors, shape factors, and process factors. The influence of materials on the manufacturing cost is described with a specific example. The article discusses the design for manufacturability to minimize the total number of parts, use readily processed materials, and eliminate machining and finishing operations. It reviews the factors influencing the selection of a material for production, including material composition, heat-treated condition, surface finish, and cost of material. The article describes the material characteristics, such as terms formability, workability, castability, machinability, and weldability, that aid or hinder the production of a part without defects.

Repair and maintenance of parts and components is carried out as a logical procedure that ensures the production of a usable and safe component or it can be approached haphazardly. This article describes the requirements and repair techniques of arc and oxyfuel welding processes to repair weld defects and structural failures. It further discusses the preliminary assessment and base-metal preparation involved in weld repair. Furthermore, the article provides information on the general repair guidelines that are followed to ensure successful weld repairs of both ferrous (carbon steels, cast irons, and stainless steels) and nonferrous (titanium) base metals.

Roll welding (ROW) is a process in which two or more sheets or plates are stacked together and then passed through the rolls until sufficient deformation has occurred to produce solid-state welds. This article begins with a process description of two modes of roll welding, including pack rolling. It describes a patented roll welding process for fabrication of heat exchangers. The article presents a table showing the typical properties of common roll welded clad laminates. The relative weldability of selected dissimilar metals and alloys roll welded into clad-laminate form are also tabulated. The article concludes with information on cladding of metals by strip roll welding.

This article discusses two categories of stainless steel casting alloys and their nomenclature. It provides information on two situations in which welding of stainless steel castings is required. These situations are based on casting defects and selection of welding processes. The article presents compositions and typical microstructures of corrosion-resistant stainless steel casting alloys in tabular form. It presents special considerations for the welding of martensitic stainless steel castings. The article reviews the two most serious problems encountered in the welding of stainless steel castings, namely, solidification hot cracking and heat-affected zone hot cracking. It concludes with a discussion on the some useful considerations for welding corrosion-resistant alloys to avoid defects.

This article focuses on the tests for evaluating the weldability, cracking susceptibility, weld pool shape, fluid flow, and weld penetration of base materials. These tests include different types of self-restraint tests, externally loaded tests for evaluating cracking susceptibility and weld penetration tests, weld pool shape tests, and Gleeble testing for evaluating weld pool shape, fluid flow, and weld penetration.

This article presents in-depth metallurgical information about the response of carbon and low-alloy steels to welding conditions and micro-structural evolution in the weld heat-affected zone. It discusses the fabrication weldability and service weldability of carbon and low-alloy steels. The article describes six general classes of the metal: low-carbon steels, high-strength low-alloy steels, quenched-and-tempered steels, heat-treatable low-alloy steels, thermal-mechanical-controlled processing steels, and chromium-molybdenum steels. It concludes with an illustration of steels' susceptibility to hydrogen-assisted cold cracking relative to carbon content and carbon equivalent.