Aluminum and its alloys are among the more formable materials of commonly fabricated metals. This article discusses the formability, bendability, and springback of aluminum and its alloys. It describes the forming limit diagrams that illustrate the biaxial combinations of strain that can occur without splitting. The article reviews various bending methods, such as draw, compression, ram and press, roll, and stretch or tension bending. It describes the process variations of incremental sheet forming (ISF), such as single-point incremental forming, two-point incremental forming, and kinematic incremental sheet forming. The article concludes with a discussion on spinning, warm forming, and superplastic forming.

This article discusses the tribology of three main sheet forming processes: deep drawing, bending, and shearing. For each process, the basic principle of the forming process is briefly explained. Tribological phenomena observed in each process, such as wear and galling, are presented. Common methods of using lubricants and coatings in sheet forming processes are also described.

Induction heating has the ability to concentrate the electromagnetic field and heat within a certain area of the workpiece. This article provides a detailed discussion on the end heating of bars, rods, and billets using solenoid inductors, oval inductors, and channel inductors. It reviews the importance of computer modeling in predicting the impact of different, interrelated, and nonlinear factors on the transitional and final thermal conditions of billets and bars. The article describes the most appropriate processes to improve end heating process effectiveness. Induction bending of narrow circumferential band of pipe or tube is also discussed. The article concludes with a discussion on stress relieving of pipe ends and welded areas.

This article is a comprehensive collection of tables containing formulas for metals processing, namely, casting and solidification, flat (sheet) rolling, conical-die extrusion, wire drawing, bending, and deep drawing. Formulas for compression, tension, and torsion testing of isotropic materials are included. The article also lists the formulas for effective stress, strain, and strain rate (isotropic material) in arbitrary and principal coordinates; dimensionless groups in fluid mechanics; and anisotropic sheet materials at various loading conditions.

This article begins with an overview of classes and applications of gray iron. It discusses the castability of gray iron in terms of section sensitivity and fluidity. The article provides information on the dimensions of prevailing sections recommended for gray irons and reviews the properties and specifications of test bar. Properties of gray iron, such as fatigue limit, pressure tightness, impact resistance, machinability, and dimensional stability, at both room and elevated temperature, are reviewed. Wear behavior of gray iron castings during sliding contact under conditions of normal lubrication is also discussed. The article evaluates the use of alloys and heat treatment to modify as-cast properties. It concludes with information on the physical properties of gray iron castings.

This article begins with a discussion on the factors considered in the selection of bending methods. It presents a detailed description of the types of bending method, machines and tools used in the bending and forming of tubing. The article provides an overview of bending tubing with and without a mandrel and hot bending. It concludes with a discussion on the bending of thin-wall tubes and lubrication for tube bending.

Bending is a common metalworking operation to create localized deformation in sheets (or blanks), plates, sections, tubes, and wires. This article emphasizes on the bending of sheet metal along with some coverage on flanging. It informs that variations in the bending stresses cause springback after bending, and discusses the variables and their effects on springback, as well as the methods to overcome or counteract them. These methods include overbending, bottoming or setting, and stretch bending. The article provides information on elastic bending, non-cylindrical bending, elastic-plastic bending, and pure plastic bending. Sheet metal bendability is a critical factor in many forming operations. The article illustrates the derivation of two relevant bend-ductility equations.

This article reviews the general characteristics of copper and copper alloys and explains how these characteristics affect the behavior of strip in different types of forming operations. These forming operations include blanking, piercing, bending, drawing and stretch forming, spinning, rubber-pad forming, and contour roll forming. Specialized forming operations such as hydraulic forming, embossing and swaging, and high-velocity metal forming are also reviewed. The article discusses the forming of smaller and larger parts from copper and copper alloy strips, as well as their property requirements and applications.

This article briefly reviews the forming of steel tailor-welded blanks (TWB) with a discussion on the effects of welding on forming. It presents the parameters that are monitored to control the stamping operation for tailor-welded blanks. The article discusses weld factors such as the orientation of weld relative to metal movement in dies, the formability of TWB materials, die and press considerations, and specific factors for the drawing, stretching, and bending of steel tailor-welded blanks.

Bars, structural shapes, and long parts are straightened by bending, twisting, or stretching. This article describes the straightening of bars, shapes, and long parts by material displacement, heating, and presses. It explains the process of parallel-roll straightening, automatic press roll straightening, moving-insert straightening, parallel-rail straightening, and epicyclic straightening. The article concludes with a discussion on straightening in bar production.

This article describes the operation procedures of wire rolling in a Turks Head machine. It discusses spring coiling, as well as the manual and power bending used in the wire forming process. The article contains a table that lists examples of several wire-forming production problems and solutions. Lubricants for wire forming such as inorganic fillers, soluble oils, and boundary lubricants are reviewed. The article also analyzes the applications of lubricants in wire forming.

This article tabulates the nominal compositions for nickel and cobalt alloys. It illustrates the comparison of strain-hardening rates of a number of alloys in terms of the increase in hardness with increasing cold reduction. The forming practice for age-hardenable alloys and the lubricants used in the forming processes of nickel and cobalt alloys are also discussed. The article summarizes the modification of tools and dies used for cold forming other metals, as the physical and mechanical properties of nickel and cobalt alloys frequently necessitate it. It discusses forming techniques for these alloys and provides several examples of these techniques, which include shearing, blanking, piercing, deep drawing, spinning, explosive forming, bending, and expanding/tube forming.

This article discusses the selection of types of stainless steel for various methods of forming based on the formability and on the power required for forming. It reviews the requirements of lubrication, blanking, and piercing. The article describes various forming methods, namely, press-brake forming, press forming, multiple-slide forming, deep drawing, spinning, rubber-pad forming, drop hammer forming¸ three-roll forming, contour roll forming, stretch forming, and bending of tubing.

This article discusses the mill products most often formed by the three-roll forming process. It schematically illustrates some of the shapes commonly produced from flat stock by the three-roll forming process. The article describes the two basic types of three-roll forming machines, namely, the pinch-roll type and the pyramid-roll type. It also lists the advantages of the pinch-roll machine, as compared to the pyramid-roll machine. The article analyzes the hot forming and cold forming processes for carbon or low alloy steel. It explains the procedure for forming truncated cones, bars, and bar sections by utilizing the pyramid-roll machine.

This article discusses the general formability considerations of aluminum alloys. To conduct a complete analysis of a formed part, the required mechanical properties, as determined by several standard tests, must be considered. The article describes tension testing and other tests designed to simulate various production forming processes, including cup tests and bend tests, which help in determining these properties. It provides information on the equipment and tools, which are used in the forming of aluminum alloys. The article presents a list of lubricants that are most widely used in the forming. It also analyzes the various forming processes of aluminum alloys. The processes include blanking and piercing, bending, press-brake forming, contour roll forming, deep drawing, spinning, stretch forming, rubber-pad forming, warm forming, superplastic forming, explosive forming, electrohydraulic forming, electromagnetic forming, hydraulic forming, shot peening, and drop hammer forming.

This article describes various bending methods: draw bending, compression bending, roll bending, stretch bending, and ram-and-press bending. It discusses the machines used for the bending of bars. These machines include devices and fixtures for manual bending, press brakes, conventional mechanical and hydraulic presses, horizontal bending machines, rotary benders, and bending presses. The article illustrates the tools used in bending and other bending process. It also tabulates the lubricants required for bending specific metals.

This article describes the effect of temperature, composition, strain rate, and fabrication history on the results obtained in the forming of beryllium as well as the safety measures required. It provides information on the equipment, tooling, dies, and workpieces used for forming beryllium. The article discusses the role of lubrication, blank development, tool designs, and strain rates, in deep drawing. It also provides information on the tooling and applications of three-roll bending, stretch forming, and spinning.

This article introduces process factors that influence die wear and lubrication for metal forming operations such as bending, spinning, stretching, deep drawing, and ironing. It discusses the effects of part shape, sheet thickness, tolerance requirements, sheet metal, and lubrication on shallow forming dies. The article describes the wear of material for dies to draw round and square cup-shaped metal parts in a press. It also discusses the effect of process conditions on the shallow forming dies.

This article contains nine tables that present useful formulas for deformation analysis and workability testing. The tables present formulas for effective stress, strain, and strain rate in arbitrary coordinates, principal, compression and tension testing of isotropic material. The article also provides formulas for flat rolling, conical-die extrusion, wire drawing, deep drawing of cups from sheet metal, and bending, and formulas for anisotropic sheet materials.