In situ process monitoring includes any technologies that monitor or inspect during an additive manufacturing (AM) process. This article presents the types, process considerations, and challenges of in situ monitoring technologies that can be implemented during an AM process. The types include system health monitoring, melt pool monitoring, and layer monitoring. The article discusses data analysis, and provides an overview of the integration of sensors into AM machines.

This article discusses technologies focused on processing plastic materials or producing direct tools used in plastics processing. The article focuses on extrusion and injection molding, covering applications, materials and their properties, equipment, processing details, part design guidelines, and special processes. It also covers the functions of the extruder, webline handling, mixing and compounding operations, and process troubleshooting. Thermoforming and mold design are covered. Various other technologies for polymer processing covered in this article are blow molding, rotational molding, compression molding, transfer molding, hand lay-up process, casting, and additive manufacturing.

Due to the recent requirement of higher integration density, solder joints are getting smaller in electronic product assemblies, which makes the joints more vulnerable to failure. Thus, the root-cause failure analysis for the solder joints becomes important to prevent failure at the assembly level. This article covers the properties of solder alloys and the corresponding intermetallic compounds. It includes the dominant failure modes introduced during the solder joint manufacturing process and in field-use applications. The corresponding failure mechanism and root-cause analysis are also presented. The article introduces several frequently used methods for solder joint failure detection, prevention, and isolation (identification for the failed location).

A mechanical part, which supports the moving part, is termed a mechanical bearing and can be classified into rolling (ball or roller) bearings and sliding bearings. This article discusses the failures of sliding bearings. It first describes the geometry of sliding bearings, next provides an overview of bearing materials, and then presents the various lubrication mechanisms: hydrostatic, hydrodynamic, boundary lubrication, elastohydrodynamic, and squeeze-film lubrication. The article describes the effect of debris and contaminant particles in bearings. The steps involved in failure analysis of sliding bearings are also covered. Finally, the article discusses wear-damage mechanisms from the standpoint of bearing design.

This article first reviews variations within the most common types of gears, namely spur, helical, worm, and straight and spiral bevel. It then provides information on gear tooth contact and gear metallurgy. This is followed by sections describing the important points of gear lubrication, the measurement of the backlash, and the necessary factors for starting the failure analysis. Next, the article explains various gear failure causes, including wear, scuffing, Hertzian fatigue, cracking, fracture, and bending fatigue, and finally presents examples of gear and reducer failure analysis.

This article discusses failure mechanisms in tool and die materials that are very important to nearly all manufacturing processes. It is primarily devoted to failures of tool steels used in cold working and hot working applications. The processes involved in the analysis of tool and die failures are also covered. In addition, the article focuses on a number of factors that are responsible for tool and die failures, including mechanical design, grade selection, steel quality, machining processes, heat treatment operation, and tool and die setup.

Directed-energy deposition (DED) is a kind of additive manufacturing (AM) technology based on synchronous powder feeding or wire feeding. This article provides a comprehensive coverage of DED for ceramic AM, beginning with an overview of DED equipment setup, followed by a discussion on DED materials and the DED deposition process. The bulk of the article is devoted to the discussion on the microstructure and properties of oxide ceramics, namely alumina and zirconia ceramics.

Material extrusion systems are the most common types of additive manufacturing systems, also known as three-dimensional (3D) printers. This article focuses on the general 3D printing processes as can be demonstrated and manipulated in desktop printers. The discussion includes details of the components involved in material extrusion as well as the melt extrusion solidification (during cooling) process, the underlying mechanism of road bonding, and the factors affecting good part quality. The discussion also covers support material, postprocessing, and road-quality considerations and the addition of infill in melt extrusion to the hollow spaces inside an object to give it structural strength. Information is also provided on different materials and associated material properties that affect the rate the printer is able to advance and retract material, thereby affecting the quality and rate at which a part is printed. The final section provides information on the mechanism of viscous extrusion 3D printing.

The aluminum alloy 4043 is recommended as a filler metal when resistance to salt water corrosion is required, especially when welding such aluminum alloys as 5052, 6061, and 6063. This datasheet provides information on key alloy metallurgy, and processing effects on tensile properties of this 4xxx series alloy.

Wrought 4xxx alloys (extrusions and forgings) exhibit high surface hardness, wear resistance, and a low coefficient of thermal expansion. This article provides a summary of brazing filler metals used to join brazeable aluminum-base metals. It contains tables that list the nominal composition and filler-metal alloys of 4xxx series used in structural forms.

This article examines aluminum forging processes, including open-die, closed-die, upset, roll, orbital, spin, and mandrel forging, and compares and contrasts their capabilities and the associated design requirements for forged parts. It discusses the effect of key process variables such as workpiece and die temperature, strain rate, and deformation mode. The article describes the relative forgeability of the ten most widely used aluminum alloys, and reviews common forging equipment, including hammers, mechanical and screw presses, and hydraulic presses. It also discusses postforge operations such as trimming, forming, repairing, cleaning, and heat treatment.

Brazing technology is continually advancing for a variety of metals including aluminum and its alloys and nonmetals. This article discusses the key physical phenomena in aluminum brazing and the materials for aluminum brazing, including base metals, filler metals, brazing sheet, and brazing flux. It describes various aluminum brazing methods, such as furnace, vacuum, dip, and torch brazing. Friction, flow, induction, resistance, and diffusion brazing are some alternate brazing methods discussed. The article reviews the brazing of aluminum to ferrous alloys, aluminum to copper, and aluminum to other nonferrous metals. It also discusses post-braze processes in terms of post-braze heat treatment and finishing. The article concludes with information on the safety precautions considered in brazing aluminum alloys.

The horsepower requirements to cut various metal alloys provide an indication of the relative ease and cost of machining, but several other important factors include cutting tool material, chip formation, cutting fluids, cutting tool wear, surface roughness, and surface integrity. This article reviews these general machining factors as well as specific cutting tool and cutting parameters for the six basic chip-forming processes of turning, shaping, milling, drilling, sawing, and broaching. Best practices for each of the six chip-forming processes are suggested for optimized machining of aluminum alloys. The article lists the inherent disadvantages of machining processes that involve compression/shear chip formation. It discusses the machining of aluminum metal-matrix composites and nontraditional machining of aluminum, such as abrasive jet, waterjet, electrodischarge, plasma arc, electrochemical, and chemical machining.

This article focuses on friction stir welding (FSW), where frictional heating and displacement of the plastic material occurs by a rapidly rotating tool traversing the weld joint. Much of the research activity early on pertained to issues related to understanding the process, such as learning about material flow, heat generation, microstructure development, and many other fundamental issues. The article summarizes the results of the research, describing the aspects of how FSW actually accomplishes sound joints in metals without melting them. It discusses the FSW process variations and the practical aspects of heat generation. The article provides information on the effect of welding on material properties and typical alloys in FSW applications. The alloys include 6061 aluminum, 5083 aluminum, 2xxx aluminum, and 7xxx aluminum alloys. The article concludes with a discussion on FSW equipment.

This article describes the direct hot extrusion process and the typical sequence of operations for producing extruded aluminum shapes from soft and medium-grade aluminum alloys, hard alloys, and aluminum-matrix composites. It discusses key process variables, including extrusion speed and exit temperature, and their effect on product quality. The article also provides information on extrusion presses, press dies, and tooling, and addresses quality issues such as surface defects, blistering, and internal cracking. It concludes with a discussion on the drawing of solid section and aluminum tube.

This article presents a brief discussion on the main applications for low- and high-viscosity polyalphaolefins (PAOs) and highlights key areas of interest and shows why PAOs are used in these applications. It discusses the physical properties of passenger car motor oils (PCMOs) based on or containing PAOs. The properties include Noack volatility and pour point. The article also discusses the properties and applications of heavy-duty engine oil (HDEO), industrial lubricants, food-grade lubricants, greases, transportation gear oils, compressor oils, hydraulic fluids, and transmission fluids.

This article describes friction force as a function of normal force in dry forming. It focuses on metal forming operations usually classified as cold working and hot working based on metallurgical considerations. The article discusses surface flattening and roughening of workpiece asperities in metal forming. It presents advanced tribology models and results for friction in isothermal forging operations in which the tooling is maintained at a temperature close to that of the workpiece. The article provides information on heat transfer models. It discusses the effect of wear in manufacturing processes. The article concludes with information on the main categories of tool and die materials used for a variety of manufacturing application.

This article is concerned with gear tooth failures influenced by friction, lubrication, and wear, and especially those failure modes that occur in wind-turbine components. It provides a detailed discussion on wear (including adhesion, abrasion, polishing, fretting, and electrical discharge), scuffing, and Hertzian fatigue (including macropitting and micropitting). Details for obtaining high lubricant specific film thickness are presented. The article describes the selection criteria for lubricants, such as oil, grease, adhesive open gear lubricant, and solid lubricants. It discusses the applications of oil and gear lubricants and the types of standardized gear tests. The article presents some recommendations for selecting lubricants and lubricant viscosity for enclosed gear. It provides some examples of failure modes that commonly occur on gears and bearings in wind turbine gearboxes.

Strategies for the lubrication of mechanical systems operating in extreme environments must exclude the liquid lubricants and greases and rely on alternative methods of lubrication, such as gases and solids. This article provides a survey of some of the more effective alternative methods of lubrication. It provides a discussion on the solid materials that have been most commonly used as lubricants: carbon-base materials, transition metal dichalcogenides, polymers, and soft metals.