1-20 of 111 Search Results for

wrought metal

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003507
EISBN: 978-1-62708-180-1
...Abstract Abstract This article describes the general root causes of failure associated with wrought metals and metalworking. This includes a brief review of the discontinuities or imperfections that may be the common sources of failure-inducing defects in bulk working of wrought products...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006835
EISBN: 978-1-62708-329-4
...Abstract Abstract The primary purpose of this article is to describe general root causes of failure that are associated with wrought metals and metalworking. This includes a brief review of the discontinuities or imperfections that may be common sources of failure-inducing defects in the bulk...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c0090114
EISBN: 978-1-62708-229-7
.... After 32,000 h of service, the blades exhibited cracking at the cooling holes. The blade material was wrought Udimet 520 alloy (Special Metals Corp.), with nominal composition of 57Ni-19Cr-12Co-6Mo-1W-2Al-3Ti-0.05C-0.005B. Figure 1 shows the blade and the airfoil cross section with the cooling holes...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006826
EISBN: 978-1-62708-329-4
... to overheating during forging operations, can also cause machining failures in wrought metals ( Ref 27 ). Grain size variation in thin products ( Ref 27 ) and secondary crystallization (also called abnormal grain growth) ( Ref 28 ) during annealing of wrought stainless steels, copper, nickel, and aluminum...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.matlhand.c9001453
EISBN: 978-1-62708-224-2
...-welded. Furthermore, the welds were at the ends and not at the sides as is usual in the case of electrically-welded chains. A transverse section from one side of a link was examined microscopically. This showed the material to be wrought-iron of satisfactory quality. It was concluded this chain sling had...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.homegoods.c9001610
EISBN: 978-1-62708-222-8
... … … … … balance 17.1 ISO 5832-1 17.0–19.0 13.0–16.0 2.25–4.2 2.0 max … 1.0 max balance ≥26.0 (a) EDS microanalysis ISO Standards: Metallic Materials for Surgical Implants Table 2 ISO Standards: Metallic Materials for Surgical Implants Material Identification Wrought...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006838
EISBN: 978-1-62708-329-4
...Abstract Abstract This article provides an overview of metal additive manufacturing (AM) processes and describes sources of failures in metal AM parts. It focuses on metal AM product failures and potential solutions related to design considerations, metallurgical characteristics, production...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001804
EISBN: 978-1-62708-241-9
.... Breme J. , Titanium and titanium alloys, biomaterials of preference . Mèmoires et É tudes Scientifiques Revue de Métallurgie , Octobre , 1989 , pp. 625 – 637 6. ISO 5832-1:2007 , Implants for surgery—Metallic materials—Part 1: Wrought stainless steel , Part 2: Commercially pure...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001108
EISBN: 978-1-62708-214-3
...Abstract Abstract The curved parts of exit pigtails made of wrought Incoloy 800H tubing used in steam reforming furnaces failed by performance after a period of service shorter than that predicted by the designers. Examination of a set of tubes consisting of both curved (perforated...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c9001683
EISBN: 978-1-62708-234-1
...×. Fig. 13 Pit, after Figure 12 . The pit wall has a generally spongy appearance. Magnification 20×. Results of analyses of the filler and wrought parent metals show that the filler or filler/parent blend has a slightly higher chromium content than the parent ( Table 1 ) as expected...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.mech.c9001684
EISBN: 978-1-62708-225-9
... . 3. Fink F. W. and Boyd W. K. , The Corrosion of Metals in Marine Environments , Report 245, Defense Metals Information Center , Battelle, Columbus, Ohio , 1970 . 4. Leidheiser H. , The Corrosion of Copper, Tin, and Their Alloys , Wiley , New York , 1971 . 5...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001339
EISBN: 978-1-62708-215-0
... the pipe axis to include the weld and base metal. Results of tensile testing are given in Table 2 . Table 3 lists typical tensile properties for wrought aluminum alloy 5083 and as-welded 5083 with 5183 filler metal. The tensile properties of the two specimens obtained from the elbow/pipe weld W-3 met...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c0046995
EISBN: 978-1-62708-232-7
... in the vicinity of the burners. The tubes had an original wall thickness of 3.0 mm (0.120 in.) and were made of three different alloys: the first was Hastelloy X; the second alloy was RA 333, a wrought nickel-base heat-resistant alloy; and the third was experimental alloy 634, which contained 72% Ni, 4% Cr...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.med.c9001690
EISBN: 978-1-62708-226-6
... implants. Corrosion Fracture mechanisms Metallic surgical implants Retrieval analysis Ti-6Al-4V UNS R56406 316L UNS S31603 ISO 5832-2 grade 1 Nitinol (Other, general, or unspecified) corrosion (Other, general, or unspecified) fracture Worldwide data indicate that approximately 100...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001819
EISBN: 978-1-62708-241-9
... analysis fatigue strength stainless steel (duplex wrought stainless steel) 316 (austenitic wrought stainless steel) UNS S31600 Introduction Methodology Results and Discussion Conclusion References References 1. “ Petroleum and natural gas industries—Materials for use in H2S...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c0046737
EISBN: 978-1-62708-229-7
.... Replacement bolts and nuts should be made from copper alloy C65100 or C65500 (wrought silicon bronze). Castings Cooling towers Dezincification UNS C86300 C86300 C86200 C46400 UNS C86200 UNS C46400 Stress-corrosion cracking Dealloying/selective leaching After 14 months of service, cracks...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001266
EISBN: 978-1-62708-215-0
... and Recommendations Selected Reference Selected Reference • Pohler O.E.M. , Failures of Metallic Orthopedic Implants , Failure Analysis and Prevention , Vol 11 , ASM Handbook , ASM International , 1986 , p 670 – 694 10.31399/asm.hb.v11.a0001819 A cast stainless steel femoral head...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006760
EISBN: 978-1-62708-295-2
... and for cleaning fracture surfaces. It discusses damage characterization of metals, covering various factors that influence the damage, namely stress, aggressive environment, temperature, and discontinuities. damage characterization failure analysis fracture surfaces metals microfractography optical...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003529
EISBN: 978-1-62708-180-1
... thiocyanate/stannous chloride Pink color Sort molybdenum-bearing stainless steels Nickel Dimethylglyoxime Red precipitate Sort 300 series from 400 series stainless steel Fig. 1 SEM image of flaky metallic contaminants determined to be a mix of steel and aluminum particles by backscatter...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.pulp.c0091622
EISBN: 978-1-62708-230-3
... of the part. Visual inspection revealed extensive weld repair and evidence of a heavy buildup of material at the abrupt change in diameter to the lower neck of the body. Figure 1(b) is a cross section through the part that shows weld metal, a piece of wrought plate that had been welded in during a repair...