1-19 of 19 Search Results for

wrought aluminum bronze

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001329
EISBN: 978-1-62708-215-0
... ( Fig. 4 ) was typical of wrought aluminum bronze material (α phase). This microstructure was found in all of the specimens examined. The socket-weld material was dendritic in appearance ( Fig. 5 ), and no evidence of cracking was found in any of the sections examined. Fig. 4 Microstructure...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001789
EISBN: 978-1-62708-241-9
... crack metallography stress intensity Al-Si bronze (wrought aluminum-silicon bronze) UNS C64200 Ni-Al bronze (wrought nickel-aluminum bronze) UNS C63200 Introduction Experimental Procedure Results and Discussion Conclusions Acknowledgments References References 1. Copper...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001082
EISBN: 978-1-62708-214-3
... the failure of the nickel-aluminum-bronze impellers showed the same type of characteristic crack initiation at the leading edge of the blades, and not in the fillet ( Fig. 2 ). A number of blade sections had undergone field welds to repair cracks or broken blades. Many of the repaired blade shapes did...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001809
EISBN: 978-1-62708-180-1
...Abstract Abstract This article discusses the classification of sliding bearings and describes the major groups of soft metal bearing materials: babbitts, copper-lead bearing alloys, bronze, and aluminum alloys. It provides a discussion on the methods for fluid-film lubrication in bearings...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006806
EISBN: 978-1-62708-329-4
... lubrication. The aluminum alloys are also superior in corrosion resistance. Aluminum alloys other than bronzes contain approximately 7% Sn and 1% Cu, with 1 or 2% Si or Mg, plus some lead and cadmium. The copper is retained in solid solution in the aluminum, but the other alloys form soft-solid particles...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006831
EISBN: 978-1-62708-329-4
... C86400 1040–1120 1900–2050 950–1040 1950–1900 C86500 1040–1120 1900–2050 950–1040 1750–1900 C86700 1040–1095 1900–2000 950–1040 1750–1900 C86800 1150–1175 1950–2150 980–1065 1800–1950 Aluminum bronze C95200 1120–1205 2050–2200 1095–1150 2000–2100 C95300 1120–1205...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003548
EISBN: 978-1-62708-180-1
.... For example, aluminum is anodic to zinc in an aqueous 1 M sodium chromate (Na 2 CrO 4 ) solution and cathodic to iron in an aqueous 1 M sodium sulfate (Na 2 SO 4 ) solution ( Ref 4 ). Emf Series The emf series is a table that lists in order the standard electrode potentials of specified...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006783
EISBN: 978-1-62708-295-2
... in the galvanic series for seawater is not necessarily valid in nonsaline solutions. For example, aluminum is anodic to zinc in an aqueous 1 M sodium chromate (Na 2 CrO 4 ) solution and cathodic to iron in an aqueous 1 M sodium sulfate (Na 2 SO 4 ) solution ( Ref 4 ). Electromotive Force Series...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003553
EISBN: 978-1-62708-180-1
... are anodic to the main body of the metal and therefore less resistant to corrosion because of precipitated phases, depletion, enrichment, or adsorption. In wrought high-strength heat treatable aluminum alloys, paths of stress-corrosion cracks are always intergranular, because the thermal treatments...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006760
EISBN: 978-1-62708-295-2
... documentation and SEM examination. Characterize wrought material by producing longitudinal and transverse sections. Each direction shows different information ( Fig. 1 ). Fig. 1 Wrought material is characterized by producing longitudinal and transverse sections. Each direction shows different...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006835
EISBN: 978-1-62708-329-4
... working of wrought products. The article addresses the types of flaws or defects that can be introduced during the steel forging process itself, including defects originating in the ingot-casting process. Defects found in nonferrous forgings—titanium, aluminum, and copper and copper alloys—also...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003529
EISBN: 978-1-62708-180-1
... that it is a carbon steel, for example, versus an alloy steel or a stainless steel will be helpful. Obviously, the experienced metals chemist will be able to tell that something is a piece of aluminum or a copper alloy or a piece of steel. More unusual alloys may cause problems. However, for many methods, where...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001812
EISBN: 978-1-62708-241-9
.... The application of LME as a failure analysis tool is also discussed. fasteners nozzles valves fracture mercury lead cadmium zinc structural alloys cracking cleavage radiography fracture toughness 5083-O (wrought aluminum magnesium alloy) UNS A95083 10Zn-2Pb (free-machining brass...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... ( Fig. 1a , b ). Parabolic or elongated shear dimples occur from torsional loading ( Fig. 1c ) or from mode II (in-plane) shear. However, metallic materials can behave in a ductile manner but not exhibit the classical dimple-rupture morphology, as shown in Fig. 1(d) for a cast aluminum alloy...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003543
EISBN: 978-1-62708-180-1
... manner, but not exhibit the classical dimple-rupture morphology, as shown in Fig. 1(d) for a cast aluminum alloy. The cast aluminum alloy fracture surface should show dimples in the aluminum matrix (original dendrites), but can be difficult to see because fracture surface morphology is impacted...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003562
EISBN: 978-1-62708-180-1
... joint on an aircraft. An aircraft structure is largely an assemblage of aluminum and steel components riveted together or joined by fasteners. Even in a simple riveted joint, there are at least three possible sites where fretting can occur ( Fig. 2 ): Between the riveted panels Between...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006834
EISBN: 978-1-62708-329-4
... Cage materials and their working-temperature domains Cage material Temperature domain (Δ T ) °C °F Steel −30 to +200 −20 to +390 Brass/bronze −30 to +200 −20 to +390 PA66 (with glass fibers) −30 to +120 −20 to +245 Polyetheretherketone −30 to +150 −20 to +300...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001810
EISBN: 978-1-62708-180-1