1-9 of 9 Search Results for

vapor-phase soldering

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003555
EISBN: 978-1-62708-180-1
... along the diffusion front. Fig. 7 Sulfidation and chloridation attack on nickel alloy of charcoal-regeneration kiln. See also Fig. 8 . Region 1 is an area of chromium sulfide islands (dark phase) interspersed in chromium-depleted region (bright phase). Region 2 has angular phase (consisting...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003570
EISBN: 978-1-62708-180-1
... and Simulated Liquid-Droplet Erosion , Microstruct. Sci. , Vol 25 , 1998 , p 183 – 190 15. Woodford D.A. , Cavitation-Erosion-Induced Phase Transformation in Alloys , Metall. Trans. , Vol 3 , 1972 , p 1137 – 1145 16. Richman R.H. , McNaughton W.P. , and Rao A.S...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003509
EISBN: 978-1-62708-180-1
... and nondestructive inspection of welds is also described in Welding, Brazing, and Soldering , Volume 6 of ASM Handbook. Service failures of welds, similar to those of any other structural component, depend on the operating environment and the nature of the applied load and may include failures from...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001817
EISBN: 978-1-62708-180-1
... a suitably buffered or inhibited solution can be used to retard corrosion. Another method is to keep the heat exchanger dry and, if necessary, fill it with an inert gas. Desiccants or vapor-phase corrosion inhibitors can also be added, and the heat exchanger can then be sealed until start-up. After start...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006794
EISBN: 978-1-62708-295-2
... phases in the solid material microstructure weakens the matrix support. This facilitates direct attack on the reinforcements and removes them from the matrix, thus reducing effectiveness of the reinforcements in wear protection ( Ref 15 , 16 ). In general, the interphase boundary is also prone...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003553
EISBN: 978-1-62708-180-1
... of soluble salts containing certain specific anions can inhibit the crack-producing effect of a given environment on a given alloy. Certain aspects of the metallurgical structure of an alloy (such as grain size, crystal structure, and number of phases) influence the susceptibility of the alloy to SCC...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003508
EISBN: 978-1-62708-180-1
... reaction, alligator skin D 135 Grooves and roughness in the vicinity of re-entrant angles on die castings Soldering, die erosion D 140: Depressions in the casting surface D 141 Casting surface depressions in the vicinity of a hot spot Sink marks, draw or suck-in D 142 Small...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... • Little distortion evident • Intergranular or transgranular • May relate to notches at surface or brittle phases internally • Progressive zone: usually transgranular with little apparent distortion • Overload zone: may be either ductile or brittle • Microstructural change typical of overheating...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003543
EISBN: 978-1-62708-180-1
... at surface or brittle phases internally • Progressive zone: usually transgranular with little apparent distortion• Overload zone: may be either ductile or brittle • Microstructural change typical of overheating• Multiple intergranular cracks• Voids formed on grain boundaries or wedge shaped cracks at grain...