1-19 of 19 Search Results for

transient torsional overloading

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001763
EISBN: 978-1-62708-241-9
.... splined shaft fatigue fracture transient torsional overloading medium carbon steel spline teeth deformation stress analysis fracture toughness SAE/AISI 1045 (medium-carbon alloy steel) UNS G10450 Introduction Visual Examination Stress Analysis Conclusions References References...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003526
EISBN: 978-1-62708-180-1
... Abstract Abstract This article provides information on the development of finite element analysis (FEA) and describes the general-purpose applications of FEA software programs in structural and thermal, static and transient, and linear and nonlinear analyses. It discusses special-purpose finite element...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006773
EISBN: 978-1-62708-295-2
...Abstract Abstract When complex designs, transient loadings, and nonlinear material behavior must be evaluated, computer-based techniques are used. This is where the finite-element analysis (FEA) is most applicable and provides considerable assistance in design analysis as well as failure...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003544
EISBN: 978-1-62708-180-1
...-life criterion gas porosity heat treatment inclusions infinite-life criterion internal bursts macropitting micropitting reversed bending rolling-contact fatigue rotational bending strengthening stress distribution subcase fatigue thermal fatigue torsional loading FATIGUE damage...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006779
EISBN: 978-1-62708-295-2
... different approximations of the fatigue diagram. The shape of the diagram depends mainly on the material, the geometry of the component, and the type of loading (axial, bending, torsion, and shear). The lines are determined by the ultimate tensile strength, S u , and the alternating fatigue strength...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006774
EISBN: 978-1-62708-295-2
... loading; elliptical dimples from shear or torsional loading). Microscale fractographic features help identify the microscopic mechanism(s) causing fracture. Figure 9 ( Ref 8 ) is a summary of the possible microstructural features associated with the basic types of external load conditions (overload...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003537
EISBN: 978-1-62708-180-1
... Rough matte fractures are ductile May indicate transition from fatigue crack growth to overload Rubbing (general) May indicate vibration May show final direction of separation Swirl pattern indicates torsion Rubbing (localized) May indicate crack closure in cyclic loading...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.9781627082952
EISBN: 978-1-62708-295-2
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003543
EISBN: 978-1-62708-180-1
...Abstract Abstract Overload failures refer to the ductile or brittle fracture of a material when stresses exceed the load-bearing capacity of a material. This article reviews some mechanistic aspects of ductile and brittle crack propagation, including a discussion on mixed-mode cracking, which...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
...Abstract Abstract This article aims to identify and illustrate the types of overload failures, which are categorized as failures due to insufficient material strength and underdesign, failures due to stress concentration and material defects, and failures due to material alteration...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001815
EISBN: 978-1-62708-180-1
... -hp) hand drill may exceed that of the loading in a 15-MW (20,000-hp) marine drive. Factors other than horsepower rating and severity of loading can affect gear strength and durability, particularly duration of loading, operating speed, transient loading, and such environmental factors as lubrication...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006811
EISBN: 978-1-62708-329-4
... arrow in each image. Fig. 14 Scanning electron microscopy micrograph showing brittle cleavage fracture morphology on a high-hardness surgical tool Fig. 15 Scanning electron microscopy micrographs showing (a) ductile overload fracture morphology on a surgical tool and (b) higher...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006819
EISBN: 978-1-62708-329-4
... Nozzle Subject to Rapid Thermal Transients , PVP2012-78359, Proceedings of the 2012 ASME Pressure Vessels and Piping Conference ( Toronto , Ontario, Canada ), 2012 10.1115/PVP2012-78359 43. Keisler J. , Chopra O.K. , and Shack W.J. , “ Fatigue Strain-Life Behavior of Carbon...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006780
EISBN: 978-1-62708-295-2
..., thermal fatigue, tension overload, and combinations of these, as modified by environment. This article briefly reviews the applied aspects of creep-related failures, where the mechanical strength of a material becomes limited by creep rather than by its elastic limit. The majority of information provided...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006838
EISBN: 978-1-62708-329-4
... aspects of PBF and DED processes have many similarities to welding but with more complicated transient conditions of heating, melting, solidification, and even reheating, with the potential of additional phase transitions. Like fusion welding, lack of fusion, porosity, and cracking are the types...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003512
EISBN: 978-1-62708-180-1
... such as a discontinuity or a notch, which produces triaxial stressing in the material. The stress riser may be macroscopic in size, such as a notch or discontinuity, or microscopic and not visible. Mechanical conditions are not the only sources of cyclic loading, which can contribute to fatigue failure. Transient...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006802
EISBN: 978-1-62708-329-4
.... Stress intensity is the controlling factor in subcritical crack growth propagation rates and the identification of the critical crack size for the onset of rapid overload (critical fracture). Stress and crack geometry are parameters that determine the stress intensity. The stress-intensity factor...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006825
EISBN: 978-1-62708-329-4
... indicating initiation of fatigue cracks from multiple locations on the right-side portion of the tube. Left side is the fast-fracture zone, indicative of failure under overload condition. (b) Ratchet marks indicative of crack initiation from multiple locations. Original magnification: 6× Fig. 3...