1-11 of 11 Search Results for

thermoset matrix composites

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003571
EISBN: 978-1-62708-180-1
... of a few formulations of thermoset composites. The relevant micrograph is given in Fig. 9 . It is seen from these results that the wear resistance of phenolic resin increases by almost two orders of magnitude when fillers such as carbon and aramid fibers are added to the phenolic resin matrix...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003572
EISBN: 978-1-62708-180-1
..., aspect ratio, distribution, orientation, combination with fillers, and the quality of bonding with the matrix), and operating conditions. Fibers are far more wear resistant than the matrix and hence control the wear of composite. Continuous fiber-reinforced composites with a thermoset-polymer matrix...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006800
EISBN: 978-1-62708-329-4
... , Addison-Wesley , 1991 7. Kardos G. , Risk and Hazard Analysis in Design , Materials Selection and Design , Vol 20 , ASM Handbook , ASM International , 1997 8. Heckel R.W. , Introduction to the Effects of Composition, Processing, and Structure on Materials Properties...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003501
EISBN: 978-1-62708-180-1
... will be made from metal, plastic, ceramic, or composite. Level II: Determine whether metal parts will be produced by a deformation process (wrought) or a casting process; for plastics, determine whether they will be thermoplastic or thermosetting polymers. Level III: Narrow options to a broad...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003522
EISBN: 978-1-62708-180-1
... microanalysis, Auger electron spectroscopy, secondary ion mass spectroscopy, and X-ray powder diffraction. The article discusses the analysis and interpretation of base material composition and microstructures. Preparation and examination of metallographic specimens in failure analysis are also discussed...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006757
EISBN: 978-1-62708-295-2
... oscillations and thus produces fluoride radicals inside the reaction chamber. These radicals then react with the silicon-containing matrix of the ceramics (SiC and Si 3 N 4 ), and the intergranular grain-boundary phase remains unattacked by plasma etching. In general, phenolic-thermosetting-resin-bonded...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006780
EISBN: 978-1-62708-295-2
.... A , Vol 84 , 1910 , p 1 – 12 10.1098/rspa.1910.0050 4. Ezrin M. , Plastics Failure Guide: Cause and Prevention , Hanser Publishers , 1996 5. Scheirs J. , Compositional and Failure Analysis of Polymers: A Practical Approach , Wiley , 2000 6. Hertzberg R.W...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003548
EISBN: 978-1-62708-180-1
... to the common structural metals and alloys. Impervious graphite, especially in heat-exchanger applications, is cathodic to the less noble metals and alloys. Carbon-filled polymers or metal-matrix composites can act as noble metals in a galvanic couple. Metal Ion Deposition Ions of a more noble metal may...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006783
EISBN: 978-1-62708-295-2
... polymers or metal-matrix composites can act as noble metals in a galvanic couple. Metal Ion Deposition Ions of a more noble metal may be reduced on the surface of a more active metal, for example, copper on aluminum or steel, or silver on copper. This process is also known as cementation, especially...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003537
EISBN: 978-1-62708-180-1
... appearance and mechanism facilitate potential scaling to fabricated engineering components. Several compilations of fractographic information (albeit dated in some instances) are also available for metals, polymers, ceramics, and composites. Examples include Ref 14 , 15 , 16 , 17 , 18 , 19 , 20...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006774
EISBN: 978-1-62708-295-2
... and composition Rolling-contact fatigue appears similar to wear in early stages Multiple intergranular fissures covered with reaction scale Grain faces may show porosity Metallographic inspection, 50 to 1000× (cross section) Grain distortion and flow near fracture Irregular...