1-20 of 454 Search Results for

temperature resistance

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006923
EISBN: 978-1-62708-395-9
... and their response to chemical, physical, and mechanical stresses whether as an unfilled, shaped article or as a component of a composite structure. It summarizes the basic thermal properties of thermoplastics and thermosets, including thermal conductivity, temperature resistance, thermal expansion, specific heat...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006925
EISBN: 978-1-62708-395-9
...) Up to 5000 (725) Up to 350 (50) Young’s modulus, GPa (10 6 psi) 15–400 (2–58) 150–450 (22–65) 0.001–10 (0.00015–1.45) High-temperature creep resistance Poor to medium Excellent … Thermal expansion Medium to high Low to medium Very high Thermal conductivity Medium to high...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006935
EISBN: 978-1-62708-395-9
...Process reinforcement capabilities and selected properties Table 1 Process reinforcement capabilities and selected properties Process Reinforcement Limitations to reinforcement Properties Surface finish (++ to −−) Flexural modulus Temperature resistance (trend) Tendency to warp...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003551
EISBN: 978-1-62708-180-1
...-carbide, silicon-nitride, or boron-nitride. Refractories and structural ceramics are generally thought to be inert and corrosion resistant (as compared to metallic alloys), and they are, relatively so, at room temperature, under dry atmosphere, and over long time intervals. With increasing...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003555
EISBN: 978-1-62708-180-1
... to be controlled by the temperature and the carbon-monoxide-to-carbon-dioxide ratio in the gas ( Ref 15 ). Nickel-base alloys are more resistant to carbon diffusion than most other alloys, and alloys with higher nickel content are superior to low-content nickel alloys. Carburization appears to be appreciable...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001818
EISBN: 978-1-62708-241-9
... in the alloys’ microstructure as secondary phase. Incoloy 800 alloy is generally used for application temperatures above 540 °C and the alloy has excellent oxidation resistance and creep resistance up to 900 °C. The fuel gas header splits into two burner trains. The modulated flow of fuel gas at constant...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c9001238
EISBN: 978-1-62708-232-7
... Abstract Heating elements, consisting of strips, 40 mm x 2 mm, of the widely used 80Ni-20Cr resistance heating alloy, and designed to withstand a temperature of 1175 deg C, were rendered unusable by scaling after a few months service in a through-type annealing furnace, Although the temperature...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c0046995
EISBN: 978-1-62708-232-7
... included replacing the material with an alloy, such as RA 333, with a higher chromium content and with an additional element, like silicon, resistant to carburization-oxidation. Carburizing Heat treating furnaces Tubes Hastelloy X UNS N06002 RA 333 UNS N06333 High-temperature corrosion...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.petrol.c9001166
EISBN: 978-1-62708-228-0
... in question, the pipes material should be a heat-resistant steel that contains more chromium and has greater resistance to hydrogen sulfide. Corrosion products Hydrogen sulfide Piping Chromium-molybdenum steel Hydrogen damage and embrittlement High-temperature corrosion and oxidation Pipes...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.machtools.c0047307
EISBN: 978-1-62708-223-5
... amount of retained austenite. This caused reduced wear resistance and thus rapid wear in service. Recommendations included avoiding an excessive austenitizing temperature and excessive cooling rates from the austenitizing temperature and controlling the chemical composition to avoid excessive...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003569
EISBN: 978-1-62708-180-1
..., heat treatment, geometry, surface roughness, residual stress, etc.), cavitation resistance depends largely on liquid property, flow speed, vibration characteristics, temperature, hydrostatic pressure, and so on. For certain materials, cavitation resistance is related to hardness, but for most metallic...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c0047598
EISBN: 978-1-62708-217-4
... surfaces confined to the HAZs of the welds. Microscopic examination of sections transverse to the weld cracks showed severe intergranular corrosion in the HAZ. The fractures appeared to be caused by loss of corrosion resistance due to sensitization, that could have been induced by the temperatures attained...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c0047199
EISBN: 978-1-62708-234-1
... that the material failed as a result of exfoliation corrosion, so an investigation was undertaken, centered around the study of thermal treatments that would increase the exfoliation resistance and still develop the required 448 MPa (65 ksi) yield strength. The results of the study concluded that rolled bar stock...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001771
EISBN: 978-1-62708-241-9
... the austenite grain represented a solid solution of Fe–Cr–Ni, whereas the grain boundaries contain lamellar layers of chromium carbide. This microstructure is suitable for creep resistance [ 8 ]. On the other hand, at high temperature, the growth of carbide in grain boundary takes place and produces...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c9001224
EISBN: 978-1-62708-232-7
... Abstract A recuperator for blast heating of a cupola furnace became unserviceable because of the brittle fracture of several finned tubes made of heat resistant cast steel containing 1.4C, 2.3Si and 28Cr. The service temperature was reported as 850 deg C. This led to the suspicion...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c0047681
EISBN: 978-1-62708-229-7
... Abstract A fluorescent liquid-penetrant inspection of an experimental stator vane of a first-stage axial compressor revealed the presence of a longitudinal crack over 50 mm (2 in.) long at the edge of a resistance seam weld. The vane was made of titanium alloy Ti-6Al-4V (AMS 4911). The crack...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.chem.c9001172
EISBN: 978-1-62708-220-4
... be checked constantly if they are not made from hydrogen-resistant steel 3 . Comparatively minor occasional temperature peaks may lead to attacks of dire consequences. In the following two examples taken from such control tests are described, especially because they illustrate the difference between...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001809
EISBN: 978-1-62708-180-1
... with inadequate lubrication or with contaminants. Tin-base babbitt is more corrosion resistant than lead-base babbitt and is easier to bond to a steel backing. Babbitts are inherently weak and strongly affected by high temperatures. For this reason, thin layers of babbitt are often applied to hacking materials...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006806
EISBN: 978-1-62708-329-4
... operated with inadequate lubrication or with contaminants but fatigue quickly. Lead alloys also corrode readily. Tin-base Babbitt is more corrosion resistant than lead-base Babbitt and is easier to bond to a steel backing. Babbitts are inherently weak and strongly affected by high temperatures...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c9001609
EISBN: 978-1-62708-229-7
... precipitates in the weld and HAZ. Softening takes place relatively quickly, while annealing at this temperature to restore corrosion resistance takes up to 4 h, depending on the specific composition of the alloy and its thermomechanical processing history. When alloy 430 is only partially annealed during...