1-13 of 13 Search Results for

sintered density

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006838
EISBN: 978-1-62708-329-4
.... This research has focused on densifying steels and nickel alloys through printing and sintering of fine powder feedstocks. Fine powders on the order of 10 μm have significant drive for sintering and can reach upward of 99% density using solid-state sintering. Printing involves the deposition of binder...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003551
EISBN: 978-1-62708-180-1
... sintering. Technical ceramics nevertheless possess a fired density as close as possible to theoretical density (with small pores and very little apparent porosity—a major difference when compared to refractories). The refractory materials to be considered can be classified as: Basic refractories...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003564
EISBN: 978-1-62708-180-1
... as materials for rolling-contact bearing components show some practical advantages over traditional bearing steels. The properties of ceramics, specifically low density and high stiffness, are of most interest to gas turbine ( Ref 1 ) and machine tool manufacturers ( Ref 2 ). High hardness, low coefficient...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006829
EISBN: 978-1-62708-295-2
... the wear evolution of a sintered steel displaying a significant fluctuation of the friction coefficient, depending on the loading condition. Adapted from Ref 42 Fig. 14 Illustration and chart of the quantification of wear rate under gross slip using the accumulated friction energy parameter...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006787
EISBN: 978-1-62708-295-2
... 49. Allen R.E. , Jansen R.J. , Rosenthal P.C. , and Vitovec F.H. , The Rate of Irreversible Hydrogen Attack of Steel at Elevated Temperatures , Proc. Am. Petrol. Inst. , Vol 41 , 1961 , p 74 50. Keeler J.H. and Davis H.M. , Density and Hydrogen Occlusion...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006764
EISBN: 978-1-62708-295-2
... be applied either in through-transmission two sides or reflection mode single side. Good sensitivity in acoustically clear material All metals and alloys, sintered carbides, glass and ceramics, rubber, structural plastics, concrete Electromagnetic testing Measures impedance of coil close to conductive...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006800
EISBN: 978-1-62708-329-4
... production history Manufacturability strengths and limitations Material composition(s) Material condition (fabrication) Material assembly technology Constitutive equations relating to properties Material properties and test procedures Density Specific heat Coefficient of thermal...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003501
EISBN: 978-1-62708-180-1
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001816
EISBN: 978-1-62708-180-1
... surface is a second convective heat-transfer mode. The steam-side heat-transfer coefficient is a function of fluid velocity, viscosity, density, and tube bore diameter. Boilers in service for some time have a fourth component to the heat-flow path: internal scale or deposits. Steam reacts with steel...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003543
EISBN: 978-1-62708-180-1
... in poorly sintered powder-metallurgy constructs. It is necessary for the practicing failure analyst to understand that intergranular brittle fracture is not always due to defects and improper processing. This mechanism can result from well-controlled processes that provide benefit that can outweigh...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
.... Intergranular brittle fracture is very prevalent in ceramic materials and is often present in poorly sintered powder metallurgy constructs. It is necessary for the practicing failure analyst to understand that intergranular brittle fracture is not always due to defects and improper processing. This mechanism...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006825
EISBN: 978-1-62708-329-4
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4