1-11 of 11 Search Results for

rigid die compaction

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006915
EISBN: 978-1-62708-395-9
..., and addresses related considerations such as melt viscosity and melt strength, crystallization, orientation, die swell, melt fracture, shrinkage, molded-in stress, and polymer degradation. composition elastic modulus engineering plastics polymer properties polymer structure shear rate...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.bldgs.c9001646
EISBN: 978-1-62708-219-8
... not only effective interlocking but also a continuous working surface for withstanding in-service wear. The compact construction and fill-factor of locked coil wire ropes make them relatively impervious to the ingress of moisture and render them less vulnerable to corrosion. However, such ropes...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006864
EISBN: 978-1-62708-395-9
... is based on careful viscosity measurements carried out in a capillary rheometer at high shear rates. The shear rates observed during extrusion range from 0 s −1 at the centerline of the flow channel to 1000’s s −1 observed along the wall of the die lips. When running extrusion operations, it is common...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006928
EISBN: 978-1-62708-395-9
... 0.19–2 150–240 22–35 60–75 9–11 95–115 HRR PA 80 12 90 3.0 0.43 85 12 … … 79 HRM, 118 HRR PMMA 50–70 7–10 2–10 … … 80–115 12–17 90–115 13–17 85–105 HRM PS 35–60 5–9 1–4 3.0–4.0 0.4–0.6 80–110 12–16 55–110 8–16 65–90 HRM PVC, rigid 40–60 6–9 5 2.4–2.7...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.9781627083959
EISBN: 978-1-62708-395-9
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003562
EISBN: 978-1-62708-180-1
... and 0.5 to 10 kHz, with no load and under full load. Although it was not possible to distinguish between elastic movement and rigid body movement, it was assumed that amplitudes >1 μm (>40 μin.) were due to the latter. The amplitude range was from 4.30 to 10 −4 μm (173 to 0.004 μin.) in die...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006831
EISBN: 978-1-62708-329-4
... of veins on the casting surface Veining or finning A 113 Network of projections on the surface of die castings Heat-checked die A 114 (a) Thin projection parallel to a casting surface, in re-entrant angles Fillet scab A 115 Thin metallic projection located at a re-entrant angle...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006923
EISBN: 978-1-62708-395-9
...–0.12 70–100 Silicone … … 260 500 0.22 0.13 80–300 Urethane elastomer … … 90 190 0.07–0.30 0.04–0.178 100–200 Urethane rigid foam … … 160 325 0.06–0.12 0.033–0.067 80 (a) UL, Underwriters Laboratories. (b) Short-term continuous service temperature. (c) Long...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006925
EISBN: 978-1-62708-395-9
.... Engineering plastics all have, as their principal constituent, one or more synthetic polymer resins and almost universally contain additives. Additives, which have much smaller molecules than polymers, provide color, flexibility, rigidity, flame resistance, weathering resistance, and/or processibility...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006779
EISBN: 978-1-62708-295-2
... initiation. The LCF tests are carried out on small, unnotched specimens under pure alternating strain cycles ( R ε = −1) ( Fig. 9 ). Fig. 9 Example of low-cycle fatigue curve for a die-cast aluminum alloy The LCF curve is usually expressed by the Manson-Coffin equation ( Ref 9 , 10 ), which...