1-13 of 13 Search Results for

pole figure

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 30 August 2021
Fig. 12 Electron backscatter diffraction maps (inverse pole figure: blue is 111, green is 101, and red is 001) taken from as-built 316L prepared using selective laser melting. Source: Ref 26 More
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.mech.c9001483
EISBN: 978-1-62708-225-9
... Abstract A steel bolt had been used to join the copper connecting strips between the poles of a 10-pole, series-connected, rotating field rotor of a synchronous motor. The exciting current was 155 amps. Failure of the bolt resulted in severe damage to the stator windings by the loosened ends...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001767
EISBN: 978-1-62708-241-9
... ( Fig. 6 ). It was reported that six transformer brackets failed while in service. Failure of the brackets resulted in a group of three pole-mounted transformers falling to the ground. Figure 1 shows a typical installation of three pole-mounted transformers, which are supported by two rows...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c9001516
EISBN: 978-1-62708-234-1
... cutting sites for damaging the coating. Analysis of the deposit in Figure 5 shows it to be Co-Ni magnetic coating along with contaminants, such as Al, Si S, Cl and K. Presence of Ca and Ti is due to the head material calcium titanate and that of Mn and Fe due to the pole-piece material manganese ferrite...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001766
EISBN: 978-1-62708-241-9
... Fig. 8 Undeformed and final deformed shapes with corresponding stress contours for the extension rod torque finite element analysis Abstract During the installation of power transmission lines across a major interstate highway, a temporary anchor stabilizing one of the poles failed...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.bldgs.c9001576
EISBN: 978-1-62708-219-8
... first produced in the area where stress concentrated most and then propagated straight across the width of the blade. Many of cracks were observed on the disk side, while less on the ring side. Fracture Surface Figure 4 shows the fracture surface. Cracks occurred first on the edge of the curved...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003520
EISBN: 978-1-62708-180-1
... of cold work during processes such as skin passing of sheet metal. Deformation textures can be determined using inverse or full pole figures. With the direct-comparison method, the diffractometer can be used to determine the amount of phases present, such as retained austenite in heat treated steels...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001762
EISBN: 978-1-62708-241-9
.... The axle was bent. A large button dent is shown in Fig. 20 with clear multiple aligned impacts. Roller dents on the journal along with barber pole dark bands indicative of malfunctioning induction hardening equipment can be seen in Fig. 21 . (Low hardness values have been observed in some of these bands...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003523
EISBN: 978-1-62708-180-1
... with computer-aided manufacturing to provide information for automated machining of a part. Figure 4 shows a computer-generated diagram of an accident scene in which a vehicle was driven into a guy wire from a power transmission pole. Fig. 4 Example of computer-generated diagram that illustrates...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006838
EISBN: 978-1-62708-329-4
... (inverse pole figure: blue is 111, green is 101, and red is 001) taken from as-built 316L prepared using selective laser melting. Source: Ref 26 The microstructure also may vary with the part being fabricated due to the variation in build models and the use of support stilts. These metallurgical...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006781
EISBN: 978-1-62708-295-2
... combined damage in TMF. A good example to illustrate the potential damage mechanisms and their interaction occurring in TMF is provided by the demand placed on a representative commercial aircraft turbine. Figure 1 provides a representative time series of the turbine entry temperature (TET) resulting...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006768
EISBN: 978-1-62708-295-2
... local yield strength, respectively. One major advantage of UIT is that it is a portable process, so it can be applied in the field on large structures where conventional peening is too difficult or undesirable. Figure 34 provides an example of UIT applied to the toe of welded joints on a large welded...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003528
EISBN: 978-1-62708-180-1
... the scope of this article, XRD techniques can also be used for the measurement of percent retained austenite ( Ref 19 ), and other phases, pole figures ( Ref 7 ), and other analyses too numerous to mention. Residual Stress in Failures and XRD Analysis The residual stresses present in a component can...