1-13 of 13 Search Results for

inside draft

Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.usage.c9001584
EISBN: 978-1-62708-236-5
... bottom, effectively crimping the wall near the 10 and 4 o'clock positions. Many sparger bottom pieces retained their original tube curvature. The lower portions of the outer shell of the neutralizer and the draft tube were shielded partially during detonation by the liquid AN that did not detonate...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001814
EISBN: 978-1-62708-241-9
... and scrubber. The syngas with entrained slag exited the combustion chamber through two concentric tubes, called the dip tube (inner) and the draft tube (outer), which were submerged at their lower end in the quench water. Because of the presence of water and since the draft tube is longer than the dip tube...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006927
EISBN: 978-1-62708-395-9
... as closely as the part design and process allow. Draft Generally accepted industry practices suggest making a draft, or taper, of a part face, of 1.5 to 2 degrees on vertical female features and walls and 4 to 6 degrees on standing male features. This draft assists with material flow during forming...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006864
EISBN: 978-1-62708-395-9
... be insulated and contain cooling lines to provide thermal separation between the hot barrel and the hopper. This prevents material from melting prematurely and forming a solid plug (referred to as a bridge) that blocks material from feeding to the extruder. Located inside the cylindrical barrel channel...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001370
EISBN: 978-1-62708-215-0
..., heat exchangers, nitrogen coolers, biological shield heat exchangers, diesel generators, air compressors, chiller condensers, and thermofluid heat exchangers. The heat is finally released to the atmosphere in an induced-draft cooling tower. The three service water pumps in this particular reactor take...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006837
EISBN: 978-1-62708-329-4
... of cleaning, inspection, and magnetic-particle testing techniques during assembly of the components onto the axle. A press is required to push the wheels and the bearings onto the axle, because the inside diameter of the wheel hubs and bearing components is smaller than the diameter of the wheel seat...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006868
EISBN: 978-1-62708-395-9
... detailed piece part development can begin, whereby each part of the product or assembly is separated out and fully defined in the three-dimensional (3D) solid model file (see Fig. 4 ). This includes all features required for the tooling fabrication, including draft, corner radii, and similar items...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006935
EISBN: 978-1-62708-395-9
... a tubular extrusion nozzle, it is also possible to orient the molecules or reinforcement perpendicular to the flow by constricting and then expanding the tube inside the nozzle while keeping the thickness constant. This stretches the extrusion radially and causes the molecules to orient around the tube...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.9781627083959
EISBN: 978-1-62708-395-9
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003508
EISBN: 978-1-62708-180-1
...; generally spherical and often coated with oxide Cold shot G 113 Spherical metallic inclusions inside blowholes or other cavities or in surface depressions (see A 311). Composition approximates that of the alloy cast but nearer to that of a eutectic Internal sweating, phosphide sweat G 120...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006808
EISBN: 978-1-62708-329-4
... (FCAW) using E71T-1 wire with a 75%Ar-25%CO 2 mixture. The welds were made on a double-V-joint preparation, where 80% of the weld thickness was put in from the inside of the drum shell. Welding was conducted in the 2G position (i.e., with the shells stacked up on top of each other and welding around...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003509
EISBN: 978-1-62708-180-1
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4