1-11 of 11 Search Results for

inertia-drive welding

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001808
EISBN: 978-1-62708-180-1
..., as well as how their alignment may be affected by deflections or distortions that can occur as a result of mechanical loads, shock, vibrations, or thermal gradients, should be considered. The method of connecting the driving or driven member to the shaft, such as press fitting, welding, or use...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006810
EISBN: 978-1-62708-329-4
... of mechanical loads, shock, vibrations, or thermal gradients, should be considered. The method of connecting the driving or driven member to the shaft, such as interference fitting, welding, or use of a threaded connection, a set screw, or a keyway, can influence failure. It is also important if power...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006814
EISBN: 978-1-62708-329-4
...: the time of occurrence (during manufacturing or in service), and the driving force (internal or external stresses). This article uses the term welded connection in contrast to the simpler term weld for deliberate reasons. A weld is a localized coalescence of metals or nonmetals produced either...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.design.c9001578
EISBN: 978-1-62708-233-4
... used so that a comparison between the two methods could be made. A strain gage was mounted at a 45° angle on the drive shaft and between the gearcase and the belt used to drive the reciprocating pump. An FM transmitter and a battery were also mounted on the drive shaft to transmit the strain...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.9781627082952
EISBN: 978-1-62708-295-2
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001810
EISBN: 978-1-62708-180-1
... Dull indentations in raceway at same spacing as rolling elements See Fretting and Indentation Wear, together with discoloration Running without lubricant or with lubricant that has hardened Wear at points of contact with cage Inertia forces acting on cage and insufficient lubricant Wear...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006773
EISBN: 978-1-62708-295-2
..., composition, or structure. It is not uncommon for the wrong material to have been used in an application that results in failure. Finally, the material is examined for inherent defects in manufacture, processing, or assembly. Microstructural defects, subsurface laminations, and welding defects are common...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003526
EISBN: 978-1-62708-180-1
... in failure. Finally, the material is examined for inherent defects in manufacture, processing, or assembly. Microstructural defects, subsurface laminations, and welding defects are common examples of materials defects that cause failure. In many cases when there is clear evidence of a materials-related...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006834
EISBN: 978-1-62708-329-4
... machines or in machines made from welded webs) To increase the load ratings of a given solution, one makes use of the line contact (rollers, needles) instead of the point contact (balls). That increase generally leads to a decrease of the maximum reachable speed limits due to the overall internal...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c9001459
EISBN: 978-1-62708-234-1
... of changes of form that gave rise to stress concentrations. The “fatigue” aspect of design became of increasing importance with the arrival of the high speed steam and, later, the internal combustion engine because of the need to reduce the scantlings in order to minimise both inertia effects and total...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006781
EISBN: 978-1-62708-295-2
... in their own right. Equipment The basic equipment required is a low thermal mass programmable furnace, a closed-loop servohydraulic mechanical test machine, and suitable extensometry. A radio-frequency (RF) heat source has essentially no thermal inertia and thus is ideal, assuming that the material...