1-20 of 110 Search Results for

high-strength steel sheet

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.marine.c9001210
EISBN: 978-1-62708-227-3
... metal was a construction steel of 60 to 75 kp/sq mm strength. Thick-walled parts of steels of such high strength must be preheated to approximately 200 deg C along the edges prior to welding to minimize the strong heat losses by the cold mass of the part. In the case under investigation this either...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.machtools.c9001229
EISBN: 978-1-62708-223-5
... stamped out of a sheet made from a 55 kp/sq mm strength steel. The saw blades were used for separating steel profiles at high rotational speeds. The cracks in question were located at the base of the teeth, i.e. at the point of highest operating stress. Metallographic examination showed that all cracks...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c9001225
EISBN: 978-1-62708-232-7
.... If the high temperature strength of these steels proved inadequate, an alloy lower in chromium would have been preferable. Annealing furnaces Cracking (fracturing) Heat resistant steels Sheet metal Sigma phase Fe-0.06C-1.98Si-25.8Cr-35.8Ni (Other, general, or unspecified) fracture Three...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006791
EISBN: 978-1-62708-295-2
... on high-strength steel sheet material. Source: Ref 58 Fig. 7 Examples of the seizure of roller-bearing elements. Source: Ref 15 , 48 Fig. 8 Example of seizure on a piston due to insufficient cooling. Source: Ref 49 Fig. 11 Intensity of galling, ranging from incipient...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006801
EISBN: 978-1-62708-329-4
...-papers/content/680093/ 2. Chen M. and Zhou D. , “ AHSS Forming Simulation for Shear Fracture and Edge Cracking ,” Great Designs in Steel Seminar, American Iron and Steel Institute , 2008 , www.AutoSteel.org 3. “ Advanced High-Strength Steels Application Guidelines Version 6.0...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001837
EISBN: 978-1-62708-241-9
... – 613 . 10.31399/asm.hb.v01.a0001034 Low C–CrMoV steel is non-corrosion resistant high-strength steel widely employed for the applications demanding high strength combined with high toughness and good weldability in the treated condition. The tensile strength of this steel in annealed condition...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003553
EISBN: 978-1-62708-180-1
... values of this parameter for maraging steels heat treated to various yield strengths and then exposed to aqueous environments are given subsequently in this article, along with a general description of the relationship of the rate of cracking to stress intensity for maraging steels and for other high...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001812
EISBN: 978-1-62708-180-1
... short-term exposure in boiler feed-pump applications. Specifications required that the bolts be made of a 12% Cr high-strength steel with a composition conforming to that of AISI type 410 stainless steel. Several bolts from three different installations were sent to the laboratory for examination...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001817
EISBN: 978-1-62708-180-1
... of expansion and that the studs had a coefficient of expansion that matched only the components made of austenitic stainless steel. Studs made of conventional stainless steel have a low yield strength and high ductility, which leads to stud elongation because of the operating temperature and load...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001272
EISBN: 978-1-62708-215-0
..., and the other five used a new design of two stiffeners per side sheet. Galvanized corrugated steel for the side sheets for the six tanks, having a nominal yield strength of 345 MPa (50 ksi), came from three different suppliers and was not separated by tank. During the accident investigation, cracks were found...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006805
EISBN: 978-1-62708-329-4
... coatings. They are sometimes sheltered from moisture or covered with a material that prevents moisture from making contact, thus drastically reducing or eliminating corrosion. For fasteners exposed to the elements, painting is universally used. The low-alloy high-strength steel conforming to ASTM...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006785
EISBN: 978-1-62708-295-2
... and industries that have experienced SCC failures include (this list is not exhaustive): Aerospace: Aluminum alloys in structural aircraft components such as landing gear and wing components, stainless steel tubing used as part of the hydraulic or fuel systems, high-strength low-alloy steel...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006775
EISBN: 978-1-62708-295-2
... (faceted nitride inclusions in a high-strength, low-alloy, or HSLA, steel) Inclusions have a low-strength interface bond (if any) with the matrix and have mechanical properties different from those of the matrix. In steels, these inclusions fall into three general groups: Stringer types...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003538
EISBN: 978-1-62708-180-1
... of a particle Growth from a precracked particle (for example, from prior working operations) Cracking in a matrix of limited ductility in which faceted particles cause stress concentration in the matrix (faceted nitride inclusions in a high-strength, low-alloy, or HSLA, steel) Inclusions tend...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001130
EISBN: 978-1-62708-214-3
... or stress relieving the cold-rolled strip in the 475 °C (885 °F) temperature range for high chromium content Not stress relieving the strip after cold rolling In addition, the small-diameter punched holes caused a stress concentration factor that aggravated the brittleness of the steel. ...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003507
EISBN: 978-1-62708-180-1
... is absorbed into the base metal, it must be removed by a bake-out heat treatment. Otherwise, severe embrittlement of the base metal may occur, especially in steels with hardnesses above approximately 35 HRC. High-strength, highly stressed parts can crack and fracture as a result of hydrogen embrittlement...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.petrol.c9001142
EISBN: 978-1-62708-228-0
... than the calculated value by reason of the residual stress. It is well known that steel with plastic deformation of about 5 % at a temperature between 200 and 300°C shows so much deteriorated mechanical property and the possibility of generation of the fracture becomes relatively high at low stress...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.chem.c9001570
EISBN: 978-1-62708-220-4
... this can be achieved by selecting a tubesheet material with strength greater than that of the tube material provided both materials have similar modulus of elasticity. In the clad tubesheet shown in Figure 1 , the grooves are cut in the carbon steel backing plate. The carbon steel used...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.petrol.c9001235
EISBN: 978-1-62708-228-0
... to its concentration and tears the metal apart. In soft steels of large strain capacity as are discussed here, separations and blisters are formed far below the yield point of the steel and an additional tensile strain may lead to fractures as well 2 , 3 . High strength steels with correspondingly low...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001816
EISBN: 978-1-62708-241-9
.... structural components superplastic deformation boundary sliding dislocation creep high-strength low alloy steel decohesions traction testing grain size elongation Ti-Nb microalloyed ultrafine-grained steel (UGS steel, general) high-strength low-alloy steel (HSLA steel, general) Introduction...