1-20 of 344 Search Results for

handling

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.chem.c9001407
EISBN: 978-1-62708-220-4
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.matlhand.9781627082242
EISBN: 978-1-62708-224-2
Image
Published: 01 June 2019
Fig. 1 3013 outer container (left) and inner container for handling and storage of plutonium-bearing materials More
Image
Published: 01 June 2019
Fig. 1 Flange-to-pipe assembly of a carbon steel header, used for handling superheated water, that cracked by fatigue because of notches at welds. (a) Section through butt-welded joint showing crack (arrow A) that originated at toe of weld on inner surface, incomplete weld penetration (arrow B More
Image
Published: 01 January 2002
Fig. 17 Flange-to-pipe assembly of a carbon steel header, used for handling superheated water, that cracked by fatigue because of notches at welds. (a) Section through butt-welded joint showing crack (arrow A) that originated at toe of weld on inner surface, incomplete weld penetration (arrow More
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c9001212
EISBN: 978-1-62708-235-8
... Abstract Operation handles produced from C45 steel showed many fine cracks at the flame hardened noses. The cracks ran from the corners of indentations caused by the tool during alignment. Metallographic investigation showed the nose was overheated during flame hardening. It was concluded...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001284
EISBN: 978-1-62708-215-0
... Abstract Compound bow handle risers that had failed in service and during assembly along with an unassembled riser were submitted for analysis. The risers were die cast from magnesium-base alloy AM60A. Inspection of the failed risers and metallurgical investigations conducted on the stock riser...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.homegoods.c0090430
EISBN: 978-1-62708-222-8
... Abstract The handle from a consumer product exhibited an apparent surface defect. The handle had been injection molded from a medium viscosity grade ABS resin. The anomalous appearance was objectionable to the assembler of the final product and resulted in a production lot being placed...
Image
Published: 01 June 2019
Fig. 1 Micrograph showing the included material within the handle. 24× More
Image
Published: 01 June 2019
Fig. 1 Handle etched with 10% nital to show the flame hardened zone (dark). 1 × More
Image
Published: 01 January 2002
Fig. 17 Micrograph showing the included material within the handle. 24× More
Image
Published: 01 December 1993
Fig. 1 Condition trays 2–5, showing normal position of all handles after cooking and removal from microwave oven. More
Image
Published: 01 December 1993
Fig. 2 Condition of the failed tray, showing one of the handles bent completely upright from its original flat position after cooking and removal from microwave oven. More
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c0047566
EISBN: 978-1-62708-235-8
... Abstract Handles welded to the top cover plate of a chemical-plant downcomer broke at the welds when the handles were used to lift the cover. The handles were fabricated of low-carbon steel rod; the cover was of type 502 stainless steel plate. The attachment welds were made with type 347...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.design.c0046079
EISBN: 978-1-62708-233-4
... Abstract After only a short time in service, oil-fired orchard heaters made of galvanized low-carbon steel pipe, 0.5 mm (0.020 in.) in thickness, became sensitive to impact, particularly during handling and storage. Most failures occurred in an area of the heater shell that normally reached...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001274
EISBN: 978-1-62708-215-0
... deflection of the tray handles that had occurred in the failed tray. Full distortion of the handles was obtained experimentally only by dropping a full hot tray on its end onto the floor. The test results indicated that the tray had slipped from the hand of the user. Bending Deflection Food packaging...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001319
EISBN: 978-1-62708-215-0
... (TGSCC). Conditions promoting the occurrence of the TGSCC included significant tensile stresses on the inside of the dished ends, the presence of surface contamination by iron due to poor handling practice using carbon steel implements, and storage in a coastal environment with an average temperature...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0009222
EISBN: 978-1-62708-180-1
... Abstract This article describes the six fundamental factors that decide a tool's performance. These are mechanical design, grade of tool steel, machining procedure, heat treatment, grinding, and handling. A deficiency in any one of the factors can lead to a tool and die failure. The article...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003567
EISBN: 978-1-62708-180-1
... means for combating corrosive wear, namely, materials selection, surface treatments, and handling-environment modifications. aqueous slurry corrosive wear grinding impact wear materials selection surface treatment three-body abrasive-corrosive wear two-body corrosive wear CORROSIVE...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003529
EISBN: 978-1-62708-180-1
... spectrometry, and wavelength-dispersive spectrometry. The article concludes with information on specimen handling. backscattered electron imaging economy test elemental composition analysis energy-dispersive spectrometry failure analysis metals microchemical analysis referee test specimen...