1-20 of 1112 Search Results for

form

Sort by
Image
Published: 01 June 2019
Fig. 2 Showing creep damage in the pipe in the form of grain boundary sliding and cracking. Unetched. More
Image
Published: 01 June 2019
Fig. 8 Different levels of accumulated creep damage in the form of grain boundary pores, as seen with the light microscope on a polished, unetched surface. The region shown is close to specimen 40B 1 shown in Figure 4 . More
Image
Published: 01 June 2019
Fig. 2 Modified form of construction. More
Image
Published: 01 June 2019
Fig. 3 Form of cracking from internal surface (× 50). More
Image
Published: 01 June 2019
Fig. 7 Oxide in the 1977 deposit. The particle at center left appears to have formed by the complete oxidation of a small metal particle. No layered oxide was seen except that surrounding metallic particles. More
Image
Published: 01 June 2019
Fig. 5 Babbit microstructure after compression and forging. (a) and (b) Crack formation and failure of β and η phases (arrows) after compression for a deformation degree of 35 and 60%, respectively. (c) After forging More
Image
Published: 01 June 2019
Fig. 1 Construction of Strands to Form the Non-rotating Rope. The middle strands and outside strands are laid in opposite directions to produce the rotation resistant properties. More
Image
Published: 30 August 2021
Fig. 4 Wrinkles form when metal flow into an area is greater than metal flow out More
Image
Published: 01 June 2019
Fig. 6 Form (shape) factors of isolated delta ferrite in the cladding of the Midland control specimens. More
Image
Published: 15 January 2021
Fig. 2 Inelastic damage (in the form of slip) manifesting on the surface of a single-crystal nickel-base superalloy after an identical monotonic load was applied at (a) 25 °C (75 °F) and (b) 650 °C (1200 °F). Source: Ref 3 More
Image
Published: 15 January 2021
Fig. 1 Visual testing inspection form checklist More
Image
Published: 15 January 2021
Fig. 53 Two views of white-etching deformation bands, termed butterflies, that formed at a growing fatigue crack in a forged, hardened alloy steel mill roll. The crack would have led to spalling in later service. These white-etching zones form from the original tempered martensite due More
Image
Published: 01 June 2019
Fig. 1 Location of failure showing saw tooth form of fatigue crack. More
Image
Published: 01 June 2019
Fig. 1 Coin exhibiting a stain in the form of a tan haze More
Image
Published: 01 June 2019
Fig. 3 Form of thread showing radius at only one side of root.(×50) More
Image
Published: 01 December 1992
Fig. 10 Fractograph of cap screw fracture face form 22.5° location. Note the straight-line fatigue striations and crescent moon (top and bottom) characteristics of reversed bending fatigue. More
Image
Published: 15 May 2022
Fig. 3 Macroradical reacting with oxygen to form a primary hydroperoxide More
Image
Published: 15 May 2022
Fig. 6 Photooxidation schemes. (a) Norrish type I reactions form carboxylic acids and esters. (b) Norrish type II reactions lead to scission of a polymer chain into two parts; a chain-end ketone group and a terminal double bond. More
Image
Published: 01 December 1992
Fig. 6 EDX spectrum obtained from an anomalous-appearing area in the material forming the pit (arrow in Fig. 7 ). More
Image
Published: 01 December 2019
Fig. 2 Bushing ( a ) deformed face, circle shows region where indentation was formed, ( b ) undeformed face of bushing More