1-11 of 11 Search Results for

floor beams

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001821
EISBN: 978-1-62708-180-1
... removal of the core. (b) Polished-and-etched surface showing crack, slag, and lack of fusion Fig. 20 Crack along the web-flange weld toe at the end reaction. Fig. 21 Cracking in floor-beam-girder connection plates. (a) Cracks in the outside web surface. (b) Cracks from the inside web...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.bldgs.c0047113
EISBN: 978-1-62708-219-8
...Abstract Abstract A portion of a 19 mm (0.75 in.) diam structural steel bolt was found on the floor of a manufacturing shop. This shop contained an overhead crane system that ran on rails supported by girders and columns. Inspection of the crane system revealed that the bolt had come from...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.design.c9001578
EISBN: 978-1-62708-233-4
... from the structural vibration, the isolators were actually amplifying the vibrations from the I-beam. To find the cause of the amplification, an impact test was performed on the microscope to determine its natural frequencies. The natural frequency of the scope on its isolation system was found...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.bldgs.c9001611
EISBN: 978-1-62708-219-8
... Recently, construction of a two-story building was in the intermediate stages of completion. The structural truss members for the second floor were being fabricated and erected. After approximately 30% of the truss members had been erected in a sequential manner, a fracture was noted on one flange section...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003549
EISBN: 978-1-62708-180-1
... of an isolated pit on the outside of the floor tank of a liquid asphalt tank. The asphalt had been leaking for some time as the surrounding area was covered with deposits and the wall thinning was significant. Courtesy of S.R. Freeman, Millennium Metallurgy, Ltd. Fig. 8 Cathodic protection of a buried...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006766
EISBN: 978-1-62708-295-2
... to elements with atomic number 5 or higher. In this technique, the specimen is irradiated with a primary beam of x-rays. This causes excitation of the atoms and ejection of the electrons from the electron shells (photoejection). The electron vacancies caused by the photoelectric effect are filled...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006764
EISBN: 978-1-62708-295-2
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.marine.c9001617
EISBN: 978-1-62708-227-3
... valuable information such as this is often only obtained by talking to the people on the shop floor who do the installation.) High levels of residual stress were considered likely to be present for the crimped couplings (SSPAs) because, according to the manufacturers (and subcontractors), no stress-relief...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001811
EISBN: 978-1-62708-180-1
..., such as hooks, chains, wire rope, slings, beams, bales, and trunnions; and built-in members such as shafts, gears, and drums. chains cranes failed shafts hooks lifting equipment wire rope LIFTING EQUIPMENT is used for raising, lowering, and transporting materials, parts, and equipment, generally...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003520
EISBN: 978-1-62708-180-1
... that are not resolvable with the light microscope. Thus, it is frequently used to determine pearlite interlamellar spacing or interparticle spacing, or examine the fine strengthening precipitates or dislocation substructure. The convergent-beam electron diffraction (CBED) technique can be used to identify precipitates...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006782
EISBN: 978-1-62708-295-2
... used as a protective lining for construction materials. Their characteristics include resistance to high temperatures and aggressive corrosion media. Applications include flooring, vessels, tanks, scrubbers, air pollution control equipment, and chimneys in a variety of industries. The linings exhibit...