1-20 of 105 Search Results for

fixtures

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 1992
Fig. 2 Bend test methods and fixtures. More
Image
Published: 15 May 2022
Fig. 8 Environmental stress cracking fixtures for strain-controlled bent test according to (a) ISO 22088-3 and (b) ASTM D543, Practice B More
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c0047602
EISBN: 978-1-62708-235-8
... Abstract Parts of 21Cr-6Ni-9Mn stainless steel that had been forged at about 815 deg C (1500 deg F) were gas tungsten arc welded. During postweld inspection, cracks were found in the HAZs of the welds. Welding had been done using a copper fixture that contacted the steel in the area of the HAZ...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c0006387
EISBN: 978-1-62708-217-4
... system. Some loads could be absorbed however, when the aircraft is subjected to G loads. Visual examination of the part revealed that cracks through the wall thickness initiated on the inner walls of the fixture. Scanning electron microscopy (SEM) and electron optical examination revealed...
Image
Published: 01 January 2002
Fig. 2 First fixture used by Lodge to simulate spalling. Source: Ref 4 More
Image
Published: 01 January 2002
Fig. 3 Second fixture used by Lodge to simulate spalling. Courtesy of J.E. McGarry More
Image
Published: 01 January 2002
Fig. 4 Trailing side of the balanced arm of Lodge's fixture More
Image
Published: 01 January 2002
Fig. 4 Fixture made from AISI O1 tool steel that cracked during oil quenching. This design is poor for liquid quenching. A nick in the fillet region helped to initiate cracking. 0.75× More
Image
Published: 01 June 2019
Fig. 1 Opened crack (a) in aluminum alloy 7075-T651 ejection seat swivel fixture that failed by SCC. Note crack propagation markings that suggest the crack initiated on the inside wall of the fixture and woody appearance of the fracture. (b) Higher-magnification view of fracture surface from More
Image
Published: 01 June 2019
Fig. 2 Door lock cycling fixture. More
Image
Published: 01 June 2019
Fig. 3 Door lock cycling fixture. More
Image
Published: 15 January 2021
Fig. 7 Test fixture for operational testing of exemplar spa pump More
Image
Published: 01 December 1993
Fig. 3 Test fixture developed and used at elevated temperature to obtain permanent deformation on cantilevered coupons cut from individual trays. More
Image
Published: 15 May 2022
Fig. 9 View of typical bent-strip fixture for polyethylenes More
Image
Published: 30 August 2021
Fig. 4 Fixture made from AISI O1 tool steel that cracked during oil quenching. This design is poor for liquid quenching. A nick in the fillet region helped to initiate cracking. Original magnification: 0.75× More
Image
Published: 15 May 2022
Fig. 42 Schematic of thermomechanical analysis sample-support fixture used to measure heat-distortion temperature. Source: Ref 88 More
Image
Published: 30 August 2021
Fig. 11 Example of melted polycarbonate light fixture shield. The material flows above approximately 155 °C (310 °F), near the upper end of heat exposure zone III. More
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.med.c9001573
EISBN: 978-1-62708-226-6
... Abstract TiN coated back surgery wires were made of Ti-6Al-4V. The reported failure was the presence of pits located in the uncoated area of the wires. The uncoated area of the wire is where the wire is fixtured in the coating chamber during coating. Examination and analysis of the pits using...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c0090932
EISBN: 978-1-62708-235-8
... to ductile overload. The forming stresses were sufficient to initiate surface ruptures, suggestive of having exceeded the forming limit. Recommendations included examining the forming process, including lubrication and workpiece fixturing. Cold drawing Cracks Wire 303 UNS S30300 Ductile fracture...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c0091727
EISBN: 978-1-62708-217-4
... with available aluminum text fixtures, with 300-series stainless steel, and then with titanium. No failures occurred in aluminum fixtures (apparently it provided cathodic protection). Failures in stainless steel fixtures occurred at the specimen pin areas, not at the sharp notches used to initiate stress...