1-9 of 9 Search Results for

fiber-reinforced polymeric matrix composites

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003572
EISBN: 978-1-62708-180-1
..., aspect ratio, distribution, orientation, combination with fillers, and the quality of bonding with the matrix), and operating conditions. Fibers are far more wear resistant than the matrix and hence control the wear of composite. Continuous fiber-reinforced composites with a thermoset-polymer matrix...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c0090460
EISBN: 978-1-62708-234-1
... was photographic silver recovery. Glass fiber reinforced composites Hydrolisis Oxidation Glass-reinforced nylon 12 Environmental cracking (plastics) A component of a water filtration unit failed while being used in service for approximately eight months. The filter system had been installed...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003525
EISBN: 978-1-62708-180-1
... of production parts. The mechanical hinges were specified to be injection molded from an impact-modified, 13% glass-fiber-reinforced nylon 6/6 resin. A resin substitution was suspected, corresponding to the supplier change. Samples representing the failed components and the original prototype parts were...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003571
EISBN: 978-1-62708-180-1
... to replace asbestos used in brake pads with aramid fibers ( Ref 18 , 28 , 29 , 30 ). Figure 8 compares the specific wear rate of a few formulations of thermoset composites. The relevant micrograph is given in Fig. 9 . It is seen from these results that the wear resistance of phenolic resin increases...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006794
EISBN: 978-1-62708-295-2
....2008.04.076 15. Trzaskoma P.P. , Corrosion Behavior of a Graphite Fiber/Magnesium Metal Matrix Composite in Aqueous Chloride Solution , Corrosion , Vol 42 , 1986 , p 609 − 613 10.5006/1.3583031 16. McCauley R.A. , Corrosion of Ceramic and Composite Materials , 2nd ed...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... rupture due to MVC is the most prevalent fracture mechanism of ductile overload failures. During deformation, cavities (or microvoids) nucleate at small particles (such as inclusions and second-phase particles) when the matrix material separates from the particle by interfacial decohesion and when...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006774
EISBN: 978-1-62708-295-2
...-, micro-, and macroscale structure. The combination of alloy composition, microstructure, macrostructure (segregation, banding, and fibering), service loading conditions (monotonic, cyclic, uniaxial, multiaxial, and so forth), service environment (chemically aggressive, low temperature, and high...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006767
EISBN: 978-1-62708-295-2
.... Experimental evidence indicates that metallic materials when plastically strained have a Poisson’s ratio of 0.5 and therefore deform under constant-volume conditions. An equivalent statement is that they are incompressible. Alternatively, polymerics have higher compressibility and, in many applications, should...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006812
EISBN: 978-1-62708-329-4
... is seldom obtained in commercial materials and therefore define acceptability standards for the producer. Effects of Using Unsuitable Alloys Specification of an alloy that is not suited to the application is frequently the cause of failure of a pressure vessel. The composition of the alloy may also...