1-10 of 10 Search Results for

electropolishing procedures

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.homegoods.c9001610
EISBN: 978-1-62708-222-8
... (depending on the surface). Electropolishing is accepted as a method to obtain final surface treatment in stainless steel and cobalt alloys in accordance to ASTM F 86–91. 9 Jewelry 2 was submitted to an electropolishing procedure and the result was qualitatively compared to the previous surface finish...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003532
EISBN: 978-1-62708-180-1
... examination grinding light microscopy metallographic specimen preparation metallographic techniques microstructure examination mounting polishing sectioning METALLOGRAPHIC EXAMINATION is one of the most important procedures used by metallurgists in failure analysis. Development of powerful...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006765
EISBN: 978-1-62708-295-2
... Abstract Metallographic examination is one of the most important procedures used by metallurgists in failure analysis. Typically, the light microscope (LM) is used to assess the nature of the material microstructure and its influence on the failure mechanism. Microstructural examination can...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006768
EISBN: 978-1-62708-295-2
... 6. Cullity B.D. , Elements of X-Ray Diffraction , 2nd ed. , Addison-Wesley , 1978 7. Klug H.P. and Alexander L.E. , X-Ray Diffraction Procedures for Polycrystalline and Amorphous Materials , 2nd ed. , Wiley-Interscience , 1974 8. Ruud C.O. , Residual...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003528
EISBN: 978-1-62708-180-1
... E 915 standard ( Ref 22 ). This procedure is also performed periodically to verify instrument conformity to specifications. The maximum acceptable stress is ±2 ksi (for steel), tensile or compressive. The verification of instrument alignment is usually performed on a stress-free powder...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001819
EISBN: 978-1-62708-180-1
... stabilization. They are used for maintaining the shape of the reconstructed bone for treatment of fractures or for corrective orthopedic operative procedures. After healing, internal fixation devices, having served their purpose, are commonly removed. Fig. 1 Typical examples for joint prostheses...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003522
EISBN: 978-1-62708-180-1
... replicas that are examined in the TEM. The procedure to prepare such replicas is time-consuming, however, so they are used only to a limited extent in failure analysis. Figure 12 shows examples of fracture surface replicas viewed in the TEM. These are carbon films deposited on the original plastic films...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006757
EISBN: 978-1-62708-295-2
... the tempering temperature is high, cementite particles precipitated during tempering lie along these boundaries. In these specific cases, the prior-austenite boundaries may be visible following the standard metallographic preparation procedures. In the situation where the prior-austenite boundaries...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003545
EISBN: 978-1-62708-180-1
... plastic) strain. Although this procedure is acceptable for research or investigation, the initial strain, which may amount to a substantial fraction of the total strain, should not be omitted from design studies and failure analyses. Therefore, as stated previously, modulus at temperature is of importance...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006780
EISBN: 978-1-62708-295-2
... it is common practice to ignore this contribution to total strain when plotting creep curves. Consequently, creep curves generally show only the time-dependent plastic strain that follows the initial elastic (and possibly plastic) strain. Although this procedure is acceptable for research and investigation...