1-13 of 13 Search Results for

chromate-free conversion coating

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c9001706
EISBN: 978-1-62708-217-4
... of the truck beam. Fig. 6 Enlarged view of the corrosion pit shown in Figure 5 . Arrow “A” marks a mottled pigment free surface and arrow “B” marks the corrosion pit. Optical examination of the fracture surface, with the unaided eye, revealed the presence of a deep corrosion pit...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003549
EISBN: 978-1-62708-180-1
... and the reduction of oxygen. Since the rates of oxidation and reduction must be equal, increasing the total reduction rate increases the rate of zinc solution. Therefore, acid solutions containing dissolved oxygen normally will be more corrosive than air-free acids. Oxygen reduction simply provides another means...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006782
EISBN: 978-1-62708-295-2
... been dissolved. Iron is nearly inert in air-free water and seawater, because there is limited cathodic reaction possible. If the surface of the metal is coated with paint or other nonconducting film, the rates of both anodic and cathodic reactions are greatly reduced, and corrosion will be retarded...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006805
EISBN: 978-1-62708-329-4
...) to become free from the spider. As a result, the bearing cap on the opposite side of the spider was overloaded, and it fractured. With the two screws and the bearing cap fractured, the drive shaft was free at one end. The effect of the free drive shaft was to overload the universal joint at the opposite end...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003507
EISBN: 978-1-62708-180-1
... bursts or chevron cracks, cracks on free surfaces, cracks on die-contacted surfaces Metal-flow-related problems: for example, end grain and poor surface performance; inhomogeneous grain size; shear bands and locally weakened structures; cold shuts, folds, and laps; flow-through defects Control...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001812
EISBN: 978-1-62708-180-1
... allowed the adjacent bearing cap (the unfailed cap) to become free from the spider. As a result, the bearing cap on the opposite side of the spider was overloaded, and it fractured. With the two screws and the bearing cap fractured, the drive shaft was free at one end. The effect of the free drive shaft...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003548
EISBN: 978-1-62708-180-1
... in protective coatings may lead to severe galvanic corrosion in the localized region of the coating imperfection. It is extremely dangerous to coat the anodic member of a couple because this may only reduce its active area, which severely accelerates the attack at these holidays in the otherwise protective...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006787
EISBN: 978-1-62708-295-2
... of deposit-forming materials into the boiler and by performing periodic chemical cleanings to remove waterside deposits. Caustic gouging can be reduced or negated by monitoring the water chemistry to reduce the amount of available free sodium hydroxide, preventing in-leakage of alkaline-producing salts...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006783
EISBN: 978-1-62708-295-2
... cathodic areas coupled to small anodic areas will aggravate galvanic corrosion and cause severe dissolution of the more active metal. The reverse situation—large anodic areas coupled to small cathodic areas—produces very little galvanic current. This is why imperfections or holidays in protective coatings...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006939
EISBN: 978-1-62708-395-9
... preventing cell adhesion and killing bacteria ( Ref 215 ). Coatings N-halamine-containing polymers Excellent antimicrobial properties without any environmental concerns and long-term stability. They promote the direct transfer of active moiety to the target site or by dissociating into free halogen...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003509
EISBN: 978-1-62708-180-1
... to an examination. As such, the engineering community now tends to make specific distinctions between the terms discontinuity and defect (or flaw). Neither construction materials nor engineered structures are free from imperfections, and welds and weld repairs are not exceptions. All welded structures contain...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003553
EISBN: 978-1-62708-180-1
... crack free. These results were considered significant because service reports indicated that the cracked pipe had been welded using a high heat input and a small number of passes and that the larger-diameter piping in the primary loop, which did not crack in service, had been welded with the use...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006785
EISBN: 978-1-62708-295-2