1-8 of 8 Search Results for

abrasive grit-blasting

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001822
EISBN: 978-1-62708-241-9
... removed the external coating by grit blasting after the leakage was observed. The failed pipe as received for failure analysis is shown in Fig. 2 . Visual inspection revealed metal loss apparently resulting from erosion caused by the water jetting out of the cracks. No mechanical damage was seen anywhere...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.usage.c9001608
EISBN: 978-1-62708-236-5
... scale is left on, although occasionally some is surface treated after rolling, say by pickling in acid or grit blasting, and then left in that condition. Fig. 1 Red hills of hematite in Northwest Australia. Rust is iron (steel) reverting to nature. Photograph by David Dare Parker reproduced...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001808
EISBN: 978-1-62708-180-1
... investigation and corrective action. Fatigue failures in shafts, such as bending fatigue, torsional fatigue, contact fatigue, and axial fatigue, are reviewed. The article provides information on the brittle fracture, ductile fracture, distortion, and corrosion of shafts. Abrasive wear and adhesive wear of metal...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006810
EISBN: 978-1-62708-329-4
... Failures ” in Failure Analysis and Prevention , Volume 11 of the ASM Handbook , 2021, and the article “Failures of Rolling-Element Bearings and Their Prevention” in this Volume. Wear Wear of metal parts is commonly classified into either of two categories: abrasive wear or adhesive wear...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006864
EISBN: 978-1-62708-395-9
... be difficult to clean and purge because abrasive purging compounds can damage the teeth of the gear pump and reduce output accuracy. Fig. 11 Operation of a gear pump. Adapted from Ref 1 Webline Handling The postextrusion handling of extruded products is called the webline unit...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003520
EISBN: 978-1-62708-180-1
..., polishing, and even handling to avoid creating artifacts that could lead to false conclusions. The investigator should preserve the fracture initiation area as it was at the time of failure. For example, any band saw cutting, abrasive-wheel cutting, or burning should be done well away from the fracture...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006816
EISBN: 978-1-62708-329-4
... and speeds Cutter shape and wear Grinding Abrasive media Feed Pickling Removal of surface layers Causes redistribution of stresses Shot and grit blasting Imparts shallow surface compressive layer Straightening Redistribution of stresses Plating...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.9781627083959
EISBN: 978-1-62708-395-9