1-20 of 61 Search Results for

abrasive erosion

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006795
EISBN: 978-1-62708-295-2
... of industries. This article describes the processes involved in erosion of ductile materials, brittle materials, and elastomers. Some examples of erosive wear failures are given on abrasive erosion, liquid impingement erosion, cavitation, and erosion-corrosion. In addition, the article provides information...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003568
EISBN: 978-1-62708-180-1
... materials with the aid of models and equations. It presents three examples of erosive wear failures, namely, abrasive erosion, erosion-corrosion, and cavitation erosion. abrasive erosion brittle materials cavitation erosion ductile materials erosion erosion corrosion EROSION...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006789
EISBN: 978-1-62708-295-2
... damage of the worn products after the tribological process. Then, the article describes some examples of wear processes, considering possible transitions and/or interactions of the mechanism of fretting wear, rolling-sliding wear, abrasive wear, and solid-particle erosion wear. The role of tribological...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c0047793
EISBN: 978-1-62708-217-4
... and the relatively smooth cavities and undercutting of the flank on this side indicated that the damage was caused by an erosion or abrasion mechanism. A relatively smooth worn area was formed at the center of each tooth due to an abrasive action and an undulating outline with undercutting was observed...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003567
EISBN: 978-1-62708-180-1
... of Pyrrhotite-Grinding Media Interaction Under Abrasive Conditions , Corrosion , Vol 43 ( No. 3 ), 1987 , p 159 – 169 10. Levy A.V. and Man Y. , “Erosion-Corrosion Mechanisms and Rates in Fe-Cr Steels,” Paper 111, Corrosion 86 (Houston), National Association of Corrosion Engineers...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003560
EISBN: 978-1-62708-180-1
... crusher wear, electronic circuit board drill wear, grinding plate wear failure analysis, impact wear of disk cutters, and identification of abrasive wear modes in martensitic steels. abrasive wear failures abrasive wear mechanisms adhesive wear erosive-type wear wear failure analysis...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001087
EISBN: 978-1-62708-214-3
... of the pump. The recommended remedial action was replacement with a pump appropriately sized for the desired pressures and flow rates for limestone slurry. Abrasive erosion Catastrophic wear Impingement erosion Rotors Slurry pipelines Ductile iron Corrosive wear Erosive wear Background...
Book Chapter

Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006790
EISBN: 978-1-62708-295-2
... broad classifications have generally been used to describe the manifestations of abrasive wear that are seen on worn parts ( Ref 8 , 9 , 10 ): gouging abrasion; high-stress, or grinding, abrasion; low-stress, or scratching, abrasion; and solid-particle erosion. In addition to the aforementioned...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006794
EISBN: 978-1-62708-295-2
.... Fig. 1 Examples of abrasive corrosion. (a) Mining shearer working in wet conditions. Source: Ref 1 . (b) Brake pad in wet or relatively aggressive environments such as saline water due to deicing salts and dirt. Source: Ref 2 . Reprinted with permission from NRS Brakes Erosion-Corrosion...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003558
EISBN: 978-1-62708-180-1
... for abrasive wear and erosion situations, and operational elements that are often significant, are given in Tables 2 and 3 . Operational attributes of nonabrasive wear Table 1 Operational attributes of nonabrasive wear Attribute Variations Motion  Rolling With slip Without slip...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c0046418
EISBN: 978-1-62708-234-1
... a surrounding member then caused the extensive abrasion shown at the left edge of Fig. 1(a) . The pitting (which showed maximum severity on the same side of the chamber on which there was mechanical abrasion) was produced by cavitation erosion resulting from the combined effects of low hardness of the metal...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001779
EISBN: 978-1-62708-241-9
... Fig. 1 A comparison between a typical cavitation pit and erosion assisted degradation [ 7 ] Abstract Material samples collected from failed booster pumps were analyzed to determine the cause of failure and assess the adequacy of the materials used in the design. The pumps had been...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003569
EISBN: 978-1-62708-180-1
... particles produced by cavitation can accelerate bearing damage. If wear particles from cavitation erosion are not removed systematically from the contact surface, these particles can cause other types of wear, such as solid-particle erosion or third-body abrasion ( Fig. 8 ). Fig. 8 Wear traces...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003570
EISBN: 978-1-62708-180-1
... Alloy to Low-Carbon Steel , Mater. Sci. Eng. A , Vol 188 , 1994 , p 251 – 254 20. Johnson M. , Mikkola D.E. , March P.A. , and Wright R.N. , The Resistance of Nickel and Iron Aluminides in Cavitation Erosion and Abrasive Wear , Wear , Vol 140 , 1990 , p 279 – 289...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003524
EISBN: 978-1-62708-180-1
... source can affect metal properties and microstructures during cutting. Therefore, dry abrasive cutoff wheels should never be used near critical surfaces that will be examined microscopically. Therefore, sectioning should be performed with jewelers' saws, precision diamond-edged, thin cutoff wheels...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006825
EISBN: 978-1-62708-329-4
..., reheater, and economizer tubes). Boiler tubes, which constitute one of the main pressure parts in a boiler, are exposed to highly adverse conditions, such as high skin temperatures, corrosive and erosive environment on their outer surface, and high-pressure, high-temperature water and/or steam from...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001822
EISBN: 978-1-62708-241-9
..., but not necessarily, accompanied by surface damage such as denting, fretting, abrasion, and so forth. No signs of mechanical damage were observed on this pipe, although it is possible that evidence of mechanical damage has been lost because of subsequent erosion. Transit fatigue can be prevented by following good...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003532
EISBN: 978-1-62708-180-1
... to the structure. Laboratory abrasive-wheel cutting is recommended to establish the desired plane of polish. The most commonly used sectioning device in the metallographic laboratory is the abrasive cutoff machine. All abrasive-wheel sectioning should be performed wet. An ample flow of coolant...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001816
EISBN: 978-1-62708-180-1
... to determine the cause and suggest corrective action. The causes of failures include tube rupture, corrosion or scaling, fatigue, erosion, and stress-corrosion cracking. The article also describes the procedures for conducting a failure analysis. boilers corrosion embrittlement erosion failure...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006765
EISBN: 978-1-62708-295-2
... to the structure. Laboratory abrasive-wheel cutting is recommended to establish the desired plane of polish. The most commonly used sectioning device in the metallographic laboratory is the abrasive cutoff machine. All abrasive-wheel sectioning should be performed wet. An ample flow of coolant...