1-15 of 15 Search Results for

abrasive belt grinding

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003567
EISBN: 978-1-62708-180-1
... Abstract This article focuses on the corrosion-wear synergism in aqueous slurry and grinding environments. It describes the effects of environmental factors on corrosive wear and provides information on the impact and three-body abrasive-corrosive wear. The article also discusses the various...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001849
EISBN: 978-1-62708-241-9
... with a scanning electron microscope (SEM) using a secondary electron detector. Microstructural and morphological characterization was conducted, after hot mounting, in as-polished and etched sections. Wet grinding, with successive abrasive SiC papers, followed by fine polishing using diamond and silica...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001808
EISBN: 978-1-62708-180-1
... investigation and corrective action. Fatigue failures in shafts, such as bending fatigue, torsional fatigue, contact fatigue, and axial fatigue, are reviewed. The article provides information on the brittle fracture, ductile fracture, distortion, and corrosion of shafts. Abrasive wear and adhesive wear of metal...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006810
EISBN: 978-1-62708-329-4
.... Design features that concentrate stress include ends of keyways, edges of press-fitted members, fillets at shoulders, and edges of oil holes. Stress concentrators produced during fabrication include grinding damage, machining marks or nicks, and quench cracks resulting from heat treating operations...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001109
EISBN: 978-1-62708-214-3
... conducted, along with simulation tests to assess the role of alkali chlorides in the corrosion process. The basic cause of degradation was found to be hot corrosion caused by the deposition of alkali sulfates and chlorides. However this degradation may have been aggravated by thermal cycling and abrasion...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006837
EISBN: 978-1-62708-329-4
... of the belt or disk were attempted to eliminate the existing pits from the fillet. This is evident in Fig. 25 and 26 , where the radial marks left by the grinding operation change direction when the pit is encountered. The wheelset reconditioning operation is as much art and experience as science...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006793
EISBN: 978-1-62708-295-2
...-to-metal contact Adhesion: a more severe wear regime characterized by material smearing and transfer Abrasion: equally severe, one-, two-, or three-body modes lead to the formation of plowing grooves Surface fatigue: more severe wear again, leading to subsurface crack nucleation...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001810
EISBN: 978-1-62708-180-1
... be easily recognized. In radial ball bearings that have been properly mounted, operated under good load conditions, and kept clean and properly lubricated, the paths of the balls on the highly polished raceways appear as dulled surfaces (similar to lapped surfaces) on which microscopic grinding scratches...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003565
EISBN: 978-1-62708-180-1
... wear regime characterized by material smearing and transfer Abrasion: equally severe, one-body or two-body modes lead to the formation of ploughing grooves Surface fatigue: more severe wear again, leading to subsurface crack nucleation and subsequent delamination or spalling of surface...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003529
EISBN: 978-1-62708-180-1
..., and dissolving the specimen. As long as a clean flat area is available on the surface of the part, analysis may proceed after a quick grinding operation on a special sanding belt. The need for the special sanding belt is because the abrasive grit must not contain any of the elements that are going to be analyzed...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006834
EISBN: 978-1-62708-329-4
... this could constitute a wearing “sponge” for the sealing lip itself by embedding potential foreign abrasive particles. In such situations and in geometries in which it is not possible to clean easily and/or safely those grease excesses, regular greasing with small quantities is then preferred, because...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.modes.c9001459
EISBN: 978-1-62708-234-1
... difficult to determine whether a fracture has been preceded by a slowly developing crack unless there has been some mutual abrasion of the crack surfaces or the ingress of some fluid medium has resulted in staining of these surfaces. The essential feature by which a simple fatigue failure in ductile...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.9781627083294
EISBN: 978-1-62708-329-4
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.a0006864
EISBN: 978-1-62708-395-9
... Length/diameter ratio is not too large Clearance between the barrel and screw is not too small Wear problems Unbalanced screw design or overuse of abrasive fillers: If pressure changes rapidly along the extruder, a screw may be unbalanced. Apply wear-resistant layers to the surfaces...
Series: ASM Handbook
Volume: 11B
Publisher: ASM International
Published: 15 May 2022
DOI: 10.31399/asm.hb.v11B.9781627083959
EISBN: 978-1-62708-395-9