1-8 of 8 Search Results for

Spools, corrosion

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001066
EISBN: 978-1-62708-214-3
... opened crack surfaces. The surfaces had a faceted morphology, indicating intergranular fracture. Cracks originated at the interface between the tube and the Teflon liner Corrosion products were found caked into the intergranular region between the liner and the spool. The portion of the liner that had...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.petrol.c0051866
EISBN: 978-1-62708-228-0
... plastically deformed. The CT failed prematurely due to low-cycle fatigue, initiating at ID corrosion pitting. Multiple fatigue cracks initiated at the bottom of ID corrosion pits, one of which predominated and propagated to the tubing OD, causing a pinhole leak. When the tubing was spooled onto the reel...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.design.c0065826
EISBN: 978-1-62708-233-4
... between parallel collector plates. It was determined that the 1008 wires failed because of corrosion fatigue. It was decided to replace all of the wires in the two zones with the highest rates of failure with cold-drawn type 304 austenitic stainless steel wire. These expensive wires, however, failed after...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003573
EISBN: 978-1-62708-180-1
.... deformation distortion distortion failure analysis elastic distortion inelastic cyclic buckling load limits ratcheting THIS HANDBOOK is organized according to four general categories of failure: fracture, corrosion, wear, and the subject of this article, distortion. One reason metals are so widely...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006797
EISBN: 978-1-62708-295-2
... VOLUME is organized according to four general categories of failure: fracture, corrosion, wear, and the subject of this article, distortion. One reason metals are so widely used as engineering materials is that they have high strength but also generally have the capability to respond to load (stress) by...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001756
EISBN: 978-1-62708-241-9
... growth rate based on variations in bulk property data, GT2009-59117 . In: Proceedings of ASME Turbo Expo 2009 , 8–12 June 2009 , Orlando, FL, USA 10. Eliaz N. , Shemesh G. , Latanision R.M. : Hot corrosion in gas turbine components . J. Eng. Fail. Anal. 9 ( 1 ), 31 – 43...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003509
EISBN: 978-1-62708-180-1
... FAILURES may be divided into two classes: those rejected after inspection and mechanical testing, and failures in service that may arise from fracture, wear, corrosion, or deformation (distortion). Causes for rejection during inspection may be either features visible on the weldment surface or subsurface...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003510
EISBN: 978-1-62708-180-1
... stresses. If this occurs, a spool shape is formed. Fig. 12 Size change due to thermal changes and phase transformation. K, core; R, surface These data show that the position of cooling curves for both the surface and the core for the quenching process must be considered with the appropriate...