1-11 of 11 Search Results for

H13 (hot-work tool steel)

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001788
EISBN: 978-1-62708-241-9
... rate H13 (hot-work tool steel) UNS T20813 Al-6063 (6xxx series, wrought aluminum-magnesium silicon alloy) UNS A96063 Introduction Observations on Die Failures in Local Extrusion Industry Fatigue Failure Approaches Employed Methodology Accuracy of Simulation Finite Element Analysis...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001848
EISBN: 978-1-62708-241-9
... of failure with significant contributions from the other damage mechanisms. forging die fracture thermal cycling wear tool steel heat checking deformation optical profilometry thermal conductivity H13 (chromium hot-work tool steel) UNS T20813 CuZn39Pb3 (copper-zinc wrought brass) UNS C38500...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001814
EISBN: 978-1-62708-180-1
... in cold-working and hot-working applications. It reviews problems introduced during mechanical design, materials selection, machining, heat treating, finish grinding, and tool and die operation. The brittle fracture of rehardened high-speed steels is also considered. Finally, failures due to seams or laps...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006818
EISBN: 978-1-62708-329-4
... of as-quenched martensite at the surface and a back-tempered region beneath it caused by frictional heat. Etched with 3% nital. Original magnification: 295× Fig. 44 Two shear knives made from AISI H13 tool steel. The knives were used to grip hot rolled bars after rolling so that they could be separated...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001849
EISBN: 978-1-62708-241-9
..., resulting in severe work roll damage as well as machine downtime and increased maintenance costs. work rolls fracture surface-initiated spalling cast steel beach marks shear ledges (chevron rays) ratchet marks heat checks SEM fractography strain rate maximum shear stress H13 (chromium hot...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c9001535
EISBN: 978-1-62708-232-7
... and hardened condition with a specified surface hardness in the range of 72 to 82° shore C (50.5 to 56.3 HRC). The composition of the failed 5% Cr-base, alloy steel second-intermediate drive roll is similar to that of a hot-work tool steel of the H13 type ( Ref 3 ). Unlike Sendzimir mill work rolls, which...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003532
EISBN: 978-1-62708-180-1
... containing soft ceramic shot filler. (Note the round particles in the epoxy at the top.) The specimen is annealed H13 hot work die steel, and it was etched with picral. Fig. 16 Light micrograph showing cutting damage (arrows at left) and a burr at the corner of a specimen of commercial-purity...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006765
EISBN: 978-1-62708-295-2
... in an epoxy mount. Fig. 7 Good edge retention obtained in a cast epoxy mount containing soft ceramic shot filler (round particles in the epoxy at the top.) The specimen is annealed H13 hot work die steel etched with picral. Grinding should commence with the finest grit size that establishes...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001768
EISBN: 978-1-62708-241-9
... Association Inc. , Branford , 1972 ), pp. 77 – 94 13. Zhang S. , Li J. , Lv H. , in Tool Wear and Formation Mechanism of White Layer When Hard Milling H13 Steel under Different Cooling/Lubrication Conditions , Advances in Mechanical Engineering ( 2014 ), pp. 1 – 8 10.1155/2014...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003508
EISBN: 978-1-62708-180-1
... casting. Cast iron, gray cast iron, malleable irons, ductile iron, low-alloy steel castings, austenitic steels, corrosion-resistant castings, and cast aluminum alloys are the materials discussed. The article describes the general types of discontinuities or imperfections for traditional casting with sand...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006792
EISBN: 978-1-62708-295-2
.../www.scientific.net/KEM.527.77 144. Carvalho N.J.M. , Veld A.H. in’t , and De Hosson J.T. , Interfacial Fatigue Stress in PVD TiN Coated Tool Steels under Rolling Contact Fatigue Conditions , Surf. Coat. Technol. , Vol 105 ( No. 1–2 ), 1998 , p 109 – 116 10.1016/S0257-8972(98)00466-6...