1-10 of 10 Search Results for

D2 (high carbon, high chromium tool steel)

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001121
EISBN: 978-1-62708-214-3
... on the surfaces of the crack ( Fig. 8 ). Fig. 8 Micrograph showing cracking that emanated from the surface toward the center of the piece (typical of quench cracking). Nital etch. 250×. Chemical analysis identified the material as AISI D2 (high-carbon/high-chromium) tool steel. Hardness...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001783
EISBN: 978-1-62708-241-9
... such as a “pin on disc” wear test should be conducted to confirm the materials selection and the value of the lubricant. The indenter material that was being used at the time of this analysis was an AISI D2 tool steel which is considered to be a high carbon, high chromium cold worked tool steel. The chemical...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001814
EISBN: 978-1-62708-180-1
... useful data are available. Consequently, the simple indentation hardness tests, generally the Rockwell C test or the Vickers test, are used to define strength differences. Such data are simple to produce and are extremely useful. The lower carbon, high-strength hot-work tool steels can be tested...
Series: ASM Handbook
Volume: 11A
Publisher: ASM International
Published: 30 August 2021
DOI: 10.31399/asm.hb.v11A.a0006818
EISBN: 978-1-62708-329-4
... and are extremely useful. The lower-carbon, high-strength hot work tool steels can be tested in tension, and such data are available for both room and elevated temperatures. Tension, compression, and hardness testing are discussed in separate articles in Mechanical Testing and Evaluation , Volume 8 of ASM...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001043
EISBN: 978-1-62708-214-3
... steel inner shell quench sleeve and the support tube had been completely through-carburized to the extent that it approached a D2 tool steel in carbide microstructure and hardness (50 to 60 HRC). This produced a very brittle, undesirable material that would fracture under only minor loading conditions...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.steel.c9001535
EISBN: 978-1-62708-232-7
... are usually made from high carbon-high chromium varieties of D2 (1.25 wt% C, 12 wt% Cr) or D4 (2.25 wt% C, 12 wt% Cr) type cold-work tool steels ( Ref 4 ) or of tungsten carbide ( Ref 5 ), second-intermediate roll steel composition is leaner in carbon content for enhanced toughness. It has been reported ( Ref...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003532
EISBN: 978-1-62708-180-1
... the phenolic resin mount and the specimen of M2 high-speed steel Fig. 1 Illustration of a cleavage fracture in a quenched and tempered low-carbon steel examined using three direct methods and three replication methods. (a) LM cross section (nickel plated). Etched with Vilella's reagent. (b) LM...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006765
EISBN: 978-1-62708-295-2
... to detect if the surface had been plated with nickel. Fig. 3 Light micrographs of specimens of 1215 carbon steel that were salt bath nitrided and mounted in different resins. (a) Thermosetting epoxy resin. (b) Phenolic thermosetting resin. (c) Methyl methacrylate thermoplastic resin. (d) Electroless...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006789
EISBN: 978-1-62708-295-2
... lubrication) Hard metals Bearing steels Against high-strength steels: bronzes and gray cast irons Diffusion treatments Weld hardfacing Phosphating Hard chromium Abrasive wear Hard metals Ceramic materials (for low stresses) White cast iron Tool steels Chromium martensitic steels Manganese-carbon steels...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... of environmentally assisted cracking (for example, transgranular stress-corrosion cracking of austenitic stainless steels). High-nitrogen austenitic stainless may also be less ductile during rapid crack growth. Fig. 4 Cleavage fracture in a carbon steel component. Scanning electron micrograph. Original...